645310
92
Zoom out
Zoom in
Previous page
1/96
Next page
92
Troubleshooting
—Continued
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t
appear?
Relocate your antenna.
•Move the AV receiver away from your TV or com-
puter.
Listen to the station in mono (page 56).
When listening to an AM station, operating the remote
controller may cause noise.
•Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work?
Make sure that the batteries are installed with the cor-
rect polarity (page 13).
Install new batteries. Don’t mix different types of bat-
teries, or old and new batteries (page 13).
Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor (page 13).
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not
work reliably when the doors are closed.
Make sure you’ve selected the correct remote control-
ler mode (page 13).
When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
Make sure you’ve entered the correct remote control
code.
Can’t control other components?
If it’s an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an cable won’t work (page 37).
Make sure you’ve selected the correct remote control-
ler mode (page 14).
If you connect an MD recorder or CD recorder to the
TAPE jacks, be sure to set make the necessary setting
(pages 52 and 80).
When learning commands, make sure that the trans-
mitting ends of both remote controllers are pointing at
each other.
Are you trying to learn from a remote controller that
cannot be used for learning? Some commands cannot
be learnt, especially those that transmit several
instructions with a single button press.
The wrong remote control code has been entered.
The entered remote control code may not be correct. If
more than one code is listed, try each one.
•With some AV components, certain buttons may not
work as expected, and some may not work at all.
•To control Onkyo components, point the remote con-
troller at the AV receiver.
•To control another manufacturer’s component, point
the remote controller at that component.
Can’t record?
On your recorder, make sure the correct input is
selected (e.g., digital or analog).
Zone 2 has turned off?
•Was the Sleep function set? The Sleep function turns
off Zone 2 as well as the AV receiver. To set the Sleep
function for Zone 2 only, see page 78.
There’s no sound?
Since the Zone 2 function and the REC OUT outputs
use the same circuitry, you cannot use Zone 2 and
record at the same time. When the [REC OUT] button
is pressed, Zone 2 is turned off.
Only components connected to analog inputs can be
played in Zone 2.
Tuner
Remote Controller
Recording
Zone 2
TX-NR702,602_En.book Page 92 Monday, July 26, 2004 11:05 AM
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR8260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR8260 in the language / languages: English as an attachment in your email.

The manual is 14,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info