645328
93
Zoom out
Zoom in
Previous page
1/96
Next page
93
Troubleshooting
—Continued
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
appear
Relocate your antenna.
•Move the AV receiver away from your TV or com-
puter.
Listen to the station in mono (page 49).
When listening to an AM station, operating the remote
controller may cause noise.
•Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
Can’t select XM radio channels (North Ameri-
can model only)
Channels cannot be selected while the indica-
tor is flashing, as tuning is in progress.
The remote controller doesn’t work
Make sure that the batteries are installed with the cor-
rect polarity (page 13).
Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor (page 13).
Make sure you’ve selected the correct remote control-
ler mode (page 14).
Make sure you’ve entered the correct remote control
code (page 86).
Can’t control other components
Make sure you’ve selected the correct remote control-
ler mode (page 14).
If you’ve connected an -capable Onkyo MD
recorder, CD recorder, or next generation HDD-com-
patible component to the TAPE IN/OUT jacks, or a
Remote Interactive Dock to the VIDEO 3 IN jacks, for
the remote controller to work properly, you must set
the Input Display to MD, CDR, or HDD (see page 46).
The entered remote control code may not be correct. If
more than one code is listed, try each one.
If none of the codes work, use the Learning function
to learn the commands of the other component’s
remote controller (page 89).
•With some AV components, certain buttons may not
work as expected, and some may not work at all.
•To control an Onkyo component that’s connected via
, point the remote controller at the AV receiver. Be
sure to enter the appropriate remote control code first
(page 87).
•To control an Onkyo component that’s not connected
via , or another manufacturer’s component, point
the remote controller at the component. Be sure to
enter the appropriate remote control code first
(page 86).
Can’t learn commands from another remote
controller
When learning commands, make sure that the trans-
mitting ends of both remote controllers are pointing at
each other.
Are you trying to learn from a remote controller that
cannot be used for learning? Some commands cannot
be learned, especially those that contain several
instructions.
Can’t record
On your recorder, make sure the correct input is
selected.
•To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (e.g., TAPE IN to TAPE OUT,
VIDEO 1 IN to VIDEO 1 OUT, or VIDEO 2 IN to
VIDEO 2 OUT).
When the Pure Audio listening mode is selected, video
recording is not possible because no video signals are
output. Select another listening mode.
The sound changes when I connect my head-
phones
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio, in which case it stays the
same.
How do I change the language of a multiplex
source
Use the “Multiplex” setting on the “Audio Adjust”
menus to select “Main” or “Sub” (page 68).
The functions don’t work
•To use , you must make an connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 38).
While Zone 2 is on, the functions do not work.
The AV receiver’s display doesn’t work
The display is turned off when the Pure Audio listen-
ing mode is selected.
Tuner
Remote Controller
Recording
Others
TX-SR804/804E_En.book Page 93 Monday, September 4, 2006 9:34 AM
93


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR804E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR804E in the language / languages: English as an attachment in your email.

The manual is 4,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR804E

Onkyo TX-SR804E User Manual - German - 184 pages

Onkyo TX-SR804E User Manual - Dutch - 184 pages

Onkyo TX-SR804E User Manual - French - 192 pages

Onkyo TX-SR804E User Manual - Italian - 184 pages

Onkyo TX-SR804E User Manual - Swedish - 184 pages

Onkyo TX-SR804E User Manual - Spanish - 192 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info