645332
92
Zoom out
Zoom in
Previous page
1/96
Next page
92
Troubleshooting
—Continued
The subwoofer produces no sound
When you play source material that contains no infor-
mation in the LFE channel, the subwoofer produces
no sound.
Make sure the speakers are configured correctly
(pages 70, 71).
The Zone 2 speakers produce no sound
The Zone 2 speakers only output sources that are con-
nected to an analog input. Check to see if the source is
connected to an analog input.
There’s no sound with a certain signal format
Check the digital audio output setting on the con-
nected device. On some games consoles, such as those
that can play DVDs, the default setting is off.
•With some DVD-Video discs, you need to select an
audio output format from a menu.
Can’t get 6.1- or 7.1-channel playback
When the ZONE 2 SPEAKERS terminals are used,
playback in the main room is reduced to 5.1-channels.
The volume cannot be set to +18 dB (99)
After the Automatic Speaker Setup function has been
used, or the volume level of each speaker has been
adjusted (pages 58, 73), the maximum possible vol-
ume setting be reduced.
Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so don’t do it.
An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesn’t work
Make sure the source material is Dolby Digital
(page 68).
The multichannel DVD input doesn’t work
Check the multichannel DVD input connections
(page 28).
•To select the multichannel DVD input, press the
[MULTI CH] input selector button.
Check the audio output settings on your DVD player.
About DTS signals
When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a mal-
function.
When DTS program material ends and the DTS bit-
stream stops, the AV receiver remains in DTS listen-
ing mode and the DTS indicator remains on. This is to
prevent noise when you use the pause, fast forward, or
fast reverse function on your player. If you switch your
player from DTS to PCM, because the AV receiver
does not switch formats immediately, you may not
hear any sound, in which case you should stop your
player for about 3 seconds, and then resume playback.
•With some CD players, you won’t be able to playback
DTS material properly even though your player is con-
nected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency
response changed) and the AV receiver doesn’t recog-
nize it as a genuine DTS signal. In such cases, you
may hear noise.
There’s no picture
Make sure that all video connecting plugs are pushed
in all the way (page 24).
Make sure that each video component is properly con-
nected.
If a video component is connected to a component
video input, your TV must be connected to the COM-
PONENT VIDEO OUT (page 25).
If a video component is connected to an HDMI input,
your TV must be connected to the HDMI OUT (only
TX-803/803E).
While the Pure Audio listening mode is selected, the
video circuitry is turned off and only the HDMI OUT
outputs video signals.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
•To watch a composite video or S-Video source on a
TV that’s connected to the COMPONENT VIDEO
OUT, select Video in the “Component Video Setup”
on page 44.
TX-SR803/803E: There’s no picture from a
source connected to an HDMI IN
If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that the TV or display
does not support the current video resolution and you
need to select another resolution on your DVD player.
The onscreen menus don’t appear
The onscreen menus do not appear on a TV that’s con-
nected to the HDMI OUT.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
The picture is distorted
On non-North American models, specify the TV sys-
tem used in your area in the “TV Format Setup” on
page 47.
•With some TVs and projectors, the onscreen setup
menus may not appear when the Scan Mode setting is
set to Non-Interlaced. In this case, select this setting
again by using the AV receiver’s display, and select
Interlaced (page 79).
The immediate display does not appear
The immediate display does not appear on a TV that’s
connected to the HDMI OUT or COMPONENT
VIDEO OUT.
Video
TX-SR803_En.book Page 92 Friday, August 26, 2005 9:26 AM
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR803 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR803 in the language / languages: English as an attachment in your email.

The manual is 5,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info