645330
74
Zoom out
Zoom in
Previous page
1/92
Next page
74
Advanced Setup—Continued
a. Maximum Volume
With this preference, you can prevent the volume being
set too high by specifying a maximum volume level.
The range is from 50 to 99. To specify no maximum vol-
ume, select Off.
b. Power On Volume
With this preference, you can specify the volume setting
to be used each time the AV receiver is turned on.
The range is MIN, 1 through 50. To use the same volume
level that was used when the AV receiver was turned off,
select Last.
c. Immediate Display
This preference determines whether or not actions, such
as selecting an input source, are displayed onscreen.
Normal: Select if your TV is 4:3.
Wide: Select if your TV is 16:9.
Off: Actions not displayed.
Even if this preference is set to Normal or Wide, actions
are not displayed on the TV or projector thats connected
to the COMPONENT VIDEO OUT.
d. Scan Mode
If the text in onscreen setup menus ickers due to com-
patibility with the connected display device (TV, projec-
tor, etc.), set the Scan Mode to Non-Interlaced.
Interlaced:Default.
Non-Interlaced:Select if the text ickers.
Depending on the display device, when Non-Inter-
laced is selected, the onscreen setup menus may not
appear. If this happens, use the AV receivers display
and repeat the procedure to revert to Interlaced.
e. Remote ID
With this setting, you can change the AV Receivers
remote control ID. You may need to change this if the
remote controllers control codes overlap with those of
another Onkyo component located in the same room.
If you change the AV receivers remote control ID, be
sure to set the same ID on both the AV receiver and
remote controller (see page 75). The default ID for
both is 1.
f. IR IN Position
When using a commercially available IR receiver, use
this setting to specify its location.
Main: Select if the IR receiver is located in the main
room.
Zone 2: Select if the IR receiver is located in, and will
be used to control Zone 2.
The digital input signal formats are available only for the
input sources that you have assigned a digital input jack;
otherwise you will see Analog indicated on the screen
(see page 42).
Normally, the AV receiver detects the signal format auto-
matically. However, if you experience either of the fol-
lowing issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS:
If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
If noise is produced when fast forwarding or reversing
a DTS CD, try setting the format to DTS.
Digital Input Signal Formats
1
Press and hold the AV receivers [DIGI-
TAL INPUT] button for about 3 seconds.
2
While Auto is displayed (about 3 sec-
onds), press the [DIGITAL INPUT] button
again to select: PCM, DTS, or Auto.
DTS or PCM: The DTS or PCM indicator,
depending on which format you have set, ashes,
and only signals in that format are output. Digital
signals in other formats are ignored.
Auto (default): The format is detected automat-
ically. If no digital input signal is present, the cor-
responding analog input is used instead.
STANDBY/ON
ZONE2
ZONE 2 LEVEL
PHONES
PURE AUDIO MULTl CH
TONE
+
STEREO
LISTENING MODE
DISPLAY
DIGITAL INPUT
RT/PTY/TP MEMORY
TUNING MODE
RETURN
TUNING / PRESET
ENTER
SETUP
DVD VIDEO 1 VIDEO 2
VCR 1 VCR 2
VIDEO 3 VIDEO 4 TAPE TUNER CD
SETUP MIC S VIDEO VIDEO
MASTER VOLUME
VIDEO 4 INPUT
LR
AUDIO
DIGITAL
OFF
STANDBY
CLEAR
DIGITAL INPUT
74


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR653E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR653E in the language / languages: English as an attachment in your email.

The manual is 10,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR653E

Onkyo TX-SR653E User Manual - Dutch, Swedish - 180 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info