Manual Onkyo TX-SR608 (page 67 of 76) (English)

481485

Zoom out

Zoom in

1/76

■ Only the front speakers produce sound

■ Only the center speaker produces sound

■ The surround speakers produce no sound

■ The center speaker produces no sound

■ The front high, front wide and surround back

speakers produce no sound

■ The subwoofer produces no sound

■ There’s no sound with a certain signal format

■ Can’t select the Pure Audio listening mode

■ Can’t get 6.1/7.1 playback

■ The speaker volume cannot be set as required

(The volume cannot be set to +18.0 dB)

■ Noise can be heard

■ The Late Night function doesn’t work

■ About DTS signals

When the Stereo or Mono listening mode is selected,

only the front speakers and subwoofer produce

sound.

—

In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set

to “Left/Right”.

Check the Speaker Configuration. 41

If you use the Dolby Pro Logic IIx Movie, Dolby Pro

Logic IIx Music, or Dolby Pro Logic IIx Game lis-

tening mode with a mono source, such as an AM

radio station or mono TV program, the sound is con-

centrated in the center speaker.

—

In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set

to “Center”.

Make sure the speakers are configured correctly. 41

When the T-D (Theater-Dimensional), Stereo or

Mono listening mode is selected, the surround

speakers produce no sound.

—

Depending on the source and current listening mode,

not much sound may be produced by the surround

speakers. Try selecting another listening mode.

—

Make sure the speakers are configured correctly. 41

When the Stereo or Mono listening mode is selected,

the center speaker produces no sound.

—

In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set

to “Left/Right”.

Make sure the speakers are configured correctly. 41

Depending on the current listening mode, no sound

may be produced by the front high, front wide and

surround back speakers. Select another listening

mode.

Not much sound may be produced by the front high,

front wide and surround back speakers with some

sources.

—

Make sure the speakers are configured correctly. 41

While Powered Zone 2 is being used, playback in the

main room is reduced to 5.1-channels and the front

high, front wide and surround back speakers produce

no sound.

When you play source material that contains no

information in the LFE channel, the subwoofer pro-

duces no sound.

—

Make sure the speakers are configured correctly. 41

Check the digital audio output setting on the con-

nected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

With some DVD-Video discs, you need to select an

audio output format from a menu.

—

Depending on the input signal, some listening modes

cannot be selected.

33–37

(European, Australian and Asian models) The

Pure Audio listening mode cannot be selected while

Zone 2 is on.

—

If no surround back speakers, front wide and front

high speakers are connected, or the Zone 2 speakers

are being used, 6.1/7.1 playback is not possible.

—

You can not always select all of the listening modes,

depending on the number of the speakers connected.

33–37

Check to see if a maximum volume has been set. 50

If the volume level of each individual speaker has

been adjusted to high positive values, then the maxi-

mum master volume possible may be reduced. Note

that the individual speaker volume levels are set

automatically after the Audyssey 2EQ

Room Cor-

rection and Speaker Setup function has been com-

pleted.

25, 42

Using cable ties to bundle audio cables with power

cords, speaker cables, and so on may degrade the

audio performance, so don’t do it.

—

An audio cable may be picking up interference. Try

repositioning your cables.

—

Make sure the source material is Dolby Digital,

Dolby Digital Plus, and Dolby TrueHD.

When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listen-

ing mode and the DTS indicator remains on. This is

to prevent noise when you use the pause, fast for-

ward, or fast reverse function on your player. If you

switch your player from DTS to PCM, because the

AV receiver does not switch formats immediately,

you may not hear any sound, in which case you

should stop your player for about three seconds, and

then resume playback.

—

With some CD and LD players, you won’t be able to

playback DTS material properly even though your

player is connected to a digital input on the AV

receiver. This is usually because the DTS bitstream

has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver

doesn’t recognize it as a genuine DTS signal. In such

cases, you may hear noise.

—

When playing DTS program material, using the

pause, fast forward, or fast reverse function on your

player may produce a short audible noise. This is not

a malfunction.

—

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR608 in the language / languages: English as an attachment in your email.

The manual is 2,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR608

Onkyo TX-SR608 User Manual - German - 148 pages

Onkyo TX-SR608 User Manual - Dutch - 148 pages

Onkyo TX-SR608 User Manual - French - 152 pages

Onkyo TX-SR608 User Manual - Italian - 148 pages

Onkyo TX-SR608 User Manual - Swedish - 148 pages

Onkyo TX-SR608 User Manual - Spanish - 152 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Onkyo TX-SR608 Manual

Product: