645336
59
Zoom out
Zoom in
Previous page
1/64
Next page
59
En
The AV receiver unexpectedly selects your iPod
as the input source
Can’t record
There’s no sound
The sound changes when I connect my
headphones
The display doesn’t work
How do I change the language of a multiplex
source
The u functions don’t work
The functions and Direct Change don’t work for
components connected via u
When performing “Audyssey 2EQ
®
Room
Correction and Speaker Setup”, the
measurement fails showing the message
“Ambient noise is too high.”.
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these set-
tings.
1. While holding down the input selector button for the input
source that you want to set, press SETUP.
2. Use e/r to change the setting.
3. Press the input selector button for the input source that you
want to set when you’ve finished.
Video Attenuation
This setting can be made for the BD/DVD, VCR/DVR,
CBL/SAT, GAME, or AUX input.
If you have a games console connected to the composite
video input, and the picture isn’t very clear, you can
attenuate the gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain is reduced by 2 dB.
When connecting UP-A1 Dock to the radio tuner
UP-HT1 (North American models)/UP-DT1
(European and Asian models) with AUTO selected
by the tuner’s Mode Selector switch, you can switch
the input source between UP-A1 Dock and the tuner,
by pressing PORT repeatedly on the front panel.
If you still can’t control your iPod, start playback by
pressing your iPod’s Play button. Remote operation
should then be possible.
Try resetting your iPod.
Depending on your iPod, some buttons may not
work as expected.
Always pause iPod playback before selecting a dif-
ferent input source. If playback is not paused, the
Direct Change function may select your iPod as the
input source by mistake during the transition
between tracks.
Recording
On your recorder, make sure the correct input is
selected.
When the Pure Audio listening mode is selected,
recording is not possible because no video signals
are output. Select another listening mode.
Zone 2
Only components connected to analog inputs can be
played in Zone 2.
Others
When a pair of headphones is connected, the listen-
ing mode is set to Stereo, unless it’s already set to
Stereo, Mono, Direct, or Pure Audio. (Pure Audio
listening mode is not available for North American
models.)
The display is turned off when the Pure Audio listen-
ing mode is selected.
Use the “Multiplex” setting on the “Audio Adjust
menu to select “Main” or “Sub”.
37
To use u, you must make an u connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected dig-
itally.
17
These functions don’t work when Zone 2 is turned
on.
17
This can be caused by any malfunction in your
speaker unit. Check if the unit produces normal
sounds.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR508 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR508 in the language / languages: English as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR508

Onkyo TX-SR508 User Manual - German - 128 pages

Onkyo TX-SR508 User Manual - Dutch - 128 pages

Onkyo TX-SR508 User Manual - French - 128 pages

Onkyo TX-SR508 User Manual - Italian - 128 pages

Onkyo TX-SR508 User Manual - Swedish - 128 pages

Onkyo TX-SR508 User Manual - Spanish - 128 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info