645317
57
Zoom out
Zoom in
Previous page
1/60
Next page
57
Troubleshooting
—Continued
The remote controller doesn’t work?
Make sure that the batteries are installed with the cor-
rect polarity (page 9).
Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor (page 9).
Make sure you’ve selected the correct remote control-
ler mode (page 10).
Make sure you’ve entered the correct remote control
code.
Can’t control other components?
Make sure you’ve selected the correct remote control-
ler mode (page 10).
If you’ve connected an -compatible Onkyo Mini-
Disc or CD recorder to the TAPE IN/OUT jacks, for
the remote controller to work properly, you must set
the display to MD or CD (see pages 31 and 53).
The wrong remote control code has been entered.
The entered remote control code may not be correct. If
more than one code is listed, try each one.
•With some AV components, certain buttons may not
work as expected, and some may not work at all.
•To control Onkyo components via , point the
remote controller at the AV receiver.
•To control Onkyo components without , or other
manufacturers’ components, point the remote control-
ler at that component.
Can’t record?
On your recorder, make sure the correct input is
selected.
•To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (e.g., TAPE IN to TAPE OUT, or
VIDEO 1 IN to VIDEO 1 OUT).
When the Pure Audio listening mode is selected,
recording is not possible because no video signals are
output. Select another listening mode.
The sound changes when I connect my head-
phones?
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio (not North American
model).
The display doesn’t work?
The display is turned off when the Pure Audio (not
North American model) listening mode is selected.
How do I change the language of a multiplex
source?
Use the “Multiplex” setting on the “4. Audio Adjust”
menu to select Main or Sub (page 47).
The functions don’t work?
•To use , you must make an connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 29).
Remote Controller
Recording
Others
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
To reset the AV receiver to its factory defaults, turn
it on and, while holding down the [VIDEO 1] button,
press the [STANDBY/ON] button. “Clear” will
appear on the display and the AV receiver will enter
Standby mode.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
TX-SR503_En.book Page 57 Friday, February 25, 2005 9:35 AM
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR503E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR503E in the language / languages: English as an attachment in your email.

The manual is 2,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR503E

Onkyo TX-SR503E User Manual - German - 118 pages

Onkyo TX-SR503E User Manual - Dutch - 118 pages

Onkyo TX-SR503E User Manual - French - 118 pages

Onkyo TX-SR503E User Manual - Italian - 118 pages

Onkyo TX-SR503E User Manual - Swedish - 118 pages

Onkyo TX-SR503E User Manual - Spanish - 118 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info