645311
50
Zoom out
Zoom in
Previous page
1/60
Next page
50
Controlling Other Components
You can use the TX-SR502/TX-SR502E’s remote con-
troller (RC-567M/RC-569M) to control your other AV
components, including those made by other manufactur-
ers. To do this you first need to enter the appropriate
remote control code for your DVD player, TV, VCR,
cable receiver, or satellite receiver. Then you need to
select the corresponding remote controller mode (see
page 10).
By entering the appropriate remote control code, the
[CD], [MD], and [CDR] mode buttons can also be used
with other manufacturer’s components (e.g., DVD, TV,
VCR, satellite or cable receiver).
Entering the appropriate remote control code for your
TV, VCR, and so on will allow you to control it with the
TX-SR502/TX-SR502E’s remote controller. You’ll need
to perform this procedure for each component that you
want to control.
If the remote controller works as expected, the code has
been entered correctly. If not, try again or try another
code.
Codes for Onkyo DVD Players
The remote control code for an Onkyo DVD player
depends on whether it’s connected via , as follows:
5001:
Use this code if you’ve connected an cable
and an analog audio cable (RCA) to your DVD
player. This is the default setting, so if you’re
using , you don’t need to change anything.
Point the remote controller at the TX-SR502/
TX-SR502E to operate the DVD player.
5002:
Use this code if your DVD player doesn’t have
an socket, or you’re not using . Point
the remote controller at the DVD player to
operate it.
Resetting the [DVD], [CD], [MD] or [CDR]
Mode Button
By default, the [DVD], [CD], [MD] & [CDR] mode but-
tons are preprogrammed with remote control codes for
controlling Onkyo components connected via . If
you’ve entered another code for a button and now want
to return to its default, perform the following procedure.
Resetting the Remote Controller
This section explains how to reset the remote controller
to its default settings.
Entering Remote Control Codes
1
Look up the remote control code for your
component.
See “Remote Control Codes” on page 51.
2
While holding down the [DVD], [TV],
[VCR], [CABLE], [SAT], [CD], [MD], or
[CDR] mode button, press the [STANDBY]
button.
3
Within 30 seconds, use the number but-
tons to enter the 4-digit remote control
code.
CD
+
10 0
CLEAR
123
456
789
V1 V2 V3
DVD MULTI CH
--/---
TAPE TUNER
INPUT
I
+
-
ENTER
S
E
T
U
P
G
U
I
D
E
R
E
T
U
R
N
E
X
I
T
T
O
P
M
E
N
U
M
E
N
U
VOL
+
-
CDR
SAT
AMP
+
_
TV VCR
CABLE
DVD
CD MD
DISC
CH
TONE
TUNER/
TAPE
DISPLAY
TV
INPUT
PREV
CH
DIMMER SLEEP
MUTING
ON STANDBY
T
V
TV CH
T
V VOL
REMOTE MODE
DVD, CD, MD,
CDR, TV, VCR,
CABLE, SAT
TV
STANDBY
I
Number
buttons
4
Select the remote controller mode, point
the remote controller at the component,
and check its operation.
Remote controller buttons that can be used in
DVD mode are shown on page 12. Those that can
be used with the TV, VCR, CABLE, and SAT
modes are shown on page 55.
1
While holding down the mode button that
you want to reset, press the TV [ ] but-
ton.
Release both buttons and wait two seconds.
2
Press the mode button again.
The mode button is reset.
1
While holding down the [AMP] mode but-
ton, press the
[STANDBY] button.
Release both buttons and wait five seconds.
2
Press the [AMP] mode button again.
The remote controller is reset.
TX-SR502_En.book Page 50 Tuesday, February 17, 2004 12:14 PM
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR502E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR502E in the language / languages: English as an attachment in your email.

The manual is 5,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR502E

Onkyo TX-SR502E User Manual - German, Dutch - 236 pages

Onkyo TX-SR502E User Manual - French - 120 pages

Onkyo TX-SR502E User Manual - Italian, Swedish - 236 pages

Onkyo TX-SR502E User Manual - Spanish - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info