Manual Onkyo TX-SR494 (page 91 of 100) (English)

686346

Zoom out

Zoom in

1/100

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

❏ Noise can be heard

• Using cable ties to bundle audio pin cables, power cords, speaker cables, etc. may degrade the audio performance. Do not bundle the cords.

• An audio cable may be picking up interference. Change the position of the cables.

❏ The beginning of audio received by an HDMI IN cannot be heard

• Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately.

❏ Sound suddenly reduces

• When using the unit for extended periods with the temperature inside the unit exceeding a certain temperature, the volume may be reduced

automatically to protect the circuits.

 Listening Modes

• To enjoy digital surround playback in formats such as Dolby Digital, you need to make a connection for audio signals with an HDMI cable, digital

coaxial cable or digital optical cable. Also, audio output need to be set to Bitstream output on the connected Blu-ray Disc player, etc.

• Press on the remote controller several times to switch the display of the main unit, and you can check the input format. When using a

BLUETOOTH connection, press the INFO button on the main unit.

Check the following if the problem persists after you have conrmed the above.

❏ Cannot select a desired listening mode

• Depending on the connection status of the speaker, some listening modes may not be selected. Refer to "Speaker Layouts and Selectable

Listening Modes" ( p53) or "Input Formats and Selectable Listening Modes" ( p59) in "Listening Mode".

❏ Cannot listen to the sound in Dolby TrueHD, Dolby Atmos or DTS-HD Master Audio format

• If the audio in Dolby TrueHD, Dolby Atmos or DTS-HD Master Audio format cannot be output correctly in the source format, set "BD video

supplementary sound" (or reencode, secondary sound, video additional audio, etc.) to "Off" in the setting of a connected Blu-ray Disc player, etc.

After changing the setting, switch the listening mode to that for each source, and conrm.

❏ About DTS signals

• With media that switches suddenly from DTS to PCM, PCM playback may not start immediately. In such a case, stop playback on the player side

for approx. 3 seconds or more. Then, resume playback. The playback will be performed normally.

• DTS playback may not be performed normally on some CD and LD players even if the player and this unit are digitally connected. If some

processing (e.g., output level adjustment, sampling frequency conversion, or frequency characteristic conversion) has been executed for the DTS

signal being output, this unit cannot recognize it as a genuine DTS signal, and noise may occur.

• While playing a DTS-compatible disc, if a pause or skip operation is performed on your player, noise may occur for a short period. This is not a

malfunction.

I have connected my Onkyo receiver to my projector thru the HDMI out but have received the message "signal out of reach". My TV which is close to the av receiver works ok when using the HDMI out. The projector is on the ceiling in line with the ceiling speakers and they work Ok when the tv is used,
How do I correct this? Submitted on 6-1-2024 at 06:37
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR494 in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR494

Onkyo TX-SR494 User Manual - German - 102 pages

Onkyo TX-SR494 User Manual - Dutch - 101 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Onkyo TX-SR494 Manual

Product: