Manual Onkyo TX-SR494 (page 86 of 100) (English)

686346

Zoom out

Zoom in

1/100

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

 1. Speaker Setup

1. Select the connected speaker conguration, and press ENTER.

Note that the image on the screen changes each time you select the number

of channels in "Speaker Channels".

Speaker Setup

Select how many speakers you have.

ENTER

Speaker Channels

Zone B Speaker

Speaker Impedance

7.1 ch

Yes

Fixed

6 ohms or above

Zone B Output Level

Subwoofer

- - -Height Speaker

2. The speaker combination selected in step 1 is displayed. "Yes" is displayed for

the selected speakers. If the setting is correct, press ENTER.

3. Select "Next" and press ENTER. Then a test tone is output from each speaker

to conrm the connection. Selecting each speaker with the cursors / will

output the test tone. Press ENTER after conrmation.

4. If there is no problem with the speaker connection, select "Next" and press

ENTER. To return to "Speaker Setup", select "Back to Speaker Setup" and

press ENTER.

 2. AccuEQ Room Calibration

Place the supplied speaker setup microphone at the listening position. The unit

automatically measures the test tones output from each speaker, and sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. This also automatically adjusts the equalizers

for the speakers, and enables correction of sound distortion caused by the

acoustic environment of the room.

• It takes between 3 and 12 minutes for calibration to be completed. Each

speaker outputs the test tone at high volume during measurement, so be

careful of your surroundings. Also, keep the room as quiet as possible during

measurement.

• If you connect a subwoofer, check the power and volume of the subwoofer.

Set the subwoofer volume to more than half.

• If the power of this unit suddenly turns off, the wires in the speaker cables

have touched the rear panel or other wires, and the protection circuit is

working. Twist the wires again securely, and make sure they do not stick out of

the speaker terminals when connecting.

1. Place the supplied speaker setup microphone at the listening position, and

connect it to the SETUP MIC jack on the main unit.

SETUP MI

When placing the speaker setup microphone on a tripod, refer to the

illustration.

2. Conrm a test tone is output from the subwoofer and press ENTER.

3. Press ENTER. Then, test tones are output from each speaker, and the

connected speakers and the noise in the surrounding environment are

automatically measured.

4. The measurement results in step 3 are displayed. Select "Next", and press

ENTER. The test tones are output again. Then, the unit automatically sets the

optimum volume level, crossover frequency, etc.

5. When the measurement is completed, the measurement results are displayed.

You can check each setting using the cursors / . Select "Save" and press

ENTER to save the settings.

6. Disconnect the speaker setup microphone.

 3. ARC Setup

To connect with an ARC-compatible TV, select "Yes". The ARC setting on this unit

turns on, and you can listen to the TV's audio through this unit.

• If you select "Yes", the HDMI CEC function is enabled and power consumption

increases during standby.

I have connected my Onkyo receiver to my projector thru the HDMI out but have received the message "signal out of reach". My TV which is close to the av receiver works ok when using the HDMI out. The projector is on the ceiling in line with the ceiling speakers and they work Ok when the tv is used,
How do I correct this? Submitted on 6-1-2024 at 06:37
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR494 in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR494

Onkyo TX-SR494 User Manual - German - 102 pages

Onkyo TX-SR494 User Manual - Dutch - 101 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Onkyo TX-SR494 Manual

Product: