686346

Onkyo TX-SR494 Manual

81
Zoom out
Zoom in
Previous page
1/100
Next page
81
Front Panel≫ Rear Panel≫ Remote≫
Contents
≫
Connections
≫
Playback
≫
Setup
≫
Setting Item Default Value Setting Details
Pairing
Information
- You can initialize the pairing information stored on
this unit.
Pressing ENTER when "Clear" is displayed
initializes the pairing information stored on this
unit.
• This function does not initialize the pairing
information on the BLUETOOTH-enabled
device. When pairing the unit again with the
device, be sure to clear the pairing information
on the BLUETOOTH-enabled device
beforehand. For information on how to clear
the pairing information, refer to the instruction
manual of the BLUETOOTH-enabled device.
Device - Displays the name of the BLUETOOTH-enabled
device connected to the unit.
• The name is not displayed when "Status" is
"Ready" and "Pairing".
Status - Displays the status of the BLUETOOTH-enabled
device connected to the unit.
"Ready": Not paired
"Pairing": Paired
"Connected": Successfully connected
• Wait for a while if "Bluetooth" cannot be selected. It can be selected when the
BLUETOOTH function is activated.
3. Power Management
Change the settings for the power-save function.
Setting Item Default Value Setting Details
Sleep Timer Off You can allow the unit to enter standby
automatically when the specied time elapses.
Select a value from "30 minutes", "60 minutes" and
"90 minutes".
"Off": The unit does not automatically enter standby
mode.
Setting Item Default Value Setting Details
Auto Standby On/Off This setting allows the unit to enter standby mode
automatically after 20 minutes of inactivity without
any video or audio input. (When "USB Power Out
at Standby" is enabled, the unit enters the HYBRID
STANDBY mode which minimizes the increase in
power consumption.)
"On": The unit automatically enters standby mode
("AUTO STBY" lights up).
"Off": The unit does not automatically enter standby
mode.
• "Auto Standby" is displayed on the main unit’s
display and TV screen 30 seconds before
entering standby mode.
• Default values vary depending on the regions.
Auto Standby in
HDMI Standby
Through
On/Off Enable or disable "Auto Standby" while "HDMI
Standby Through" is on.
"On": The setting is enabled.
"Off": The setting is disabled.
• This setting cannot be set to "On" if "Auto
Standby" and "HDMI Standby Through" are set
to "Off".
• Default values vary depending on the regions.
USB Power Out
at Standby
Off When this function is set to "On", electricity can be
supplied to the Streaming media player connected
to the POWER OUT port even if this unit is in
standby mode.
• The POWER OUT jack is cannot supply power to
smart phones/tablets or other devices.
• While using this function, power consumption
increases in standby mode, however, the
increase in power consumption is minimized by
automatically entering the HYBRID STANDBY
mode where only the essential circuits are
operating.
… 81 …


Need help? Post your question in this forum.

Forumrules
1

Forum

onkyo-tx-sr494

Reset search

  • I have connected my Onkyo receiver to my projector thru the HDMI out but have received the message "signal out of reach". My TV which is close to the av receiver works ok when using the HDMI out. The projector is on the ceiling in line with the ceiling speakers and they work Ok when the tv is used,
    How do I correct this? Submitted on 6-1-2024 at 06:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR494 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR494 in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR494

Onkyo TX-SR494 User Manual - German - 102 pages

Onkyo TX-SR494 User Manual - Dutch - 101 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info