686346

Onkyo TX-SR494 Manual

73
Zoom out
Zoom in
Previous page
1/100
Next page
73
Front Panel≫ Rear Panel≫ Remote≫
Contents
≫
Connections
≫
Playback
≫
Setup
≫
2. Crossover
Change the settings of crossover frequencies.
Setting Item Default Value Setting Details
Front 100 Hz Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
• If "Conguration" - "Subwoofer" is set to "No",
"Front" is xed to "Full Band", and the low
pitched range of the other channels is output
from the front speakers. Refer to the instruction
manual of your speakers to make the setting.
Center 100 Hz Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Front" is
set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Conguration" - "Speaker Channels" matches
the number of connected channels.
Height 100 Hz Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Front" is
set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Conguration" - "Speaker Channels" matches
the number of connected channels.
Setting Item Default Value Setting Details
Surround 100 Hz Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Front" is
set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Conguration" - "Speaker Channels" matches
the number of connected channels.
Surround Back 100 Hz Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when
"Surround" is set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Conguration" - "Speaker Channels" matches
the number of connected channels.
LPF of LFE 120 Hz Set the low-pass lter for LFE (low-frequency
effect) signals in order to pass only the lower
frequency signals than the set value, and thus
cancel unwanted noises. The low-pass lter is
effective only on sources with LFE channel.
The value from "80 Hz" to "120 Hz" can be set.
"Off": When this function is not used
Double Bass On This can be selected only when "Conguration"
- "Subwoofer" is set to "Yes" and "Front" is set to
"Full Band".
Bass output is boosted by feeding bass sounds
from the front right and left, and center speakers to
the subwoofer.
"On": Bass output is boosted.
"Off": Bass output is not boosted.
• This function is not automatically set even if
AccuEQ Room Calibration is performed.
… 73 …


Need help? Post your question in this forum.

Forumrules
1

Forum

onkyo-tx-sr494

Reset search

  • I have connected my Onkyo receiver to my projector thru the HDMI out but have received the message "signal out of reach". My TV which is close to the av receiver works ok when using the HDMI out. The projector is on the ceiling in line with the ceiling speakers and they work Ok when the tv is used,
    How do I correct this? Submitted on 6-1-2024 at 06:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR494 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR494 in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR494

Onkyo TX-SR494 User Manual - German - 102 pages

Onkyo TX-SR494 User Manual - Dutch - 101 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info