601876
11
Zoom out
Zoom in
Previous page
1/88
Next page
Step 2: Setting Up
Step 2: Setting Up
En-11
3� Select the settings for the connected speakers, the
type of the height speakers, and other appropriate
settings�
AccuEQ Room Calibration
Select how many speakers you have.
Ne xt
ENTER
Speaker Channels
Subwoofer
Height Speaker
7.1ch
Yes
---
When the screen above is displayed, set the items with
the cursor buttons on the remote controller.
Refer to the on-screen diagram for "Speaker Channels",
which changes each time a different number of channels
is selected. When all the items have been set, press
ENTER on the remote controller. After that, follow the
guidance displayed on the TV screen to operate the unit.
Refer to the content of an item, which appears on
the lower left of the screen when the cursor is on the
item.
4� The test tones sound from the connected speakers
and automatic speaker setting starts�
Measurement will be made three times or more for each
speaker. It takes several minutes to be completed. Keep
the room as quiet as possible during measurement. If
any of the speakers do not produce the test tone, check
for disconnection.
During measurement, each speaker outputs the test
tones at a high volume. Be careful of sound leak
that may disturb your neighbors, or be careful not to
frighten young children.
To cancel measurement on the way, disconnect the
microphone plug.
5� When the measurement is completed, the
measurement result is displayed�
Press
t
/
u
on the remote controller to check the
settings. Press ENTER with "Save" selected. Select
"On" in the next screen and press ENTER on the remote
controller.
You should normally select "On (All Channels)", and
to disable just the front speakers, you should select
"On (Except Front Left/Right)".
If there is an error message, follow the on-screen
instruction to remove the error cause.
6� When "Please unplug setup microphone�" is
displayed, disconnect the microphone�
3 HDMI Setup
The unit supports the linked system function such as power
on/off link when connected via HDMI cable with a CEC
(Consumer Electronics Control) compliant TV or player. You
need to change the default setting to use the linked system
function, HDMI Standby Through function and ARC (Audio
Return Channel) function.
HDMI CEC (RIHD)
The following linked operations are possible with connected
equipment when the CEC function is enabled.
Turning the TV to standby mode will turn the unit to
standby mode.
On the TV side, it is possible to set whether to output
audio from the speakers connected to the unit or from the
TV's speakers.
Starting playback of a CEC compliant player/recorder will
automatically switch the unit's input to the HDMI input of
the player/recorder. If the unit is in standby mode, it will
automatically be turned on.
It is also possible to control the connected CEC compliant
equipment with the remote controller of the unit. For details,
see the Advanced Manual.
¼ RIHD is a name for the linked system function of Onkyo's CEC compliant
products.
1� After pressing RECEIVER, press SETUP on the
remote controller
2� Select "5� Hardware" with the cursor and press
ENTER�
3� Select "HDMI" with the cursor and press ENTER�
4� Select "HDMI CEC (RIHD)" with the cursor and
select "On"�
When setting is complete, press SETUP to close the
menu screen.
HDMI Standby Through
The function allows transmission from players to the TV
even if the unit is in standby. Setting the HDMI CEC (RIHD)
setting mentioned above to "On" enables this setting
automatically.
Power consumption in standby mode increases when
the HDMI Standby Through function is enabled.
ARC (Audio Return Channel)
Simple connection to the ARC compatible TV using a single
HDMI cable allows to listen to the TV audio signals from
the speakers connected to the unit. Setting the HDMI CEC
(RIHD) setting mentioned above to "On" enables the "Audio
Return Channel" setting automatically.
Audio output of connected players
To enjoy digital surround sound including Dolby
Digital and DTS, audio output should be set to
"Bitstream output" on the connected Blu-ray Disc
Player or other device.
Depending on the settings on the Blu-ray Disc Player,
there may be cases when Dolby TrueHD, Dolby
Atmos, and DTS-HD Master Audio is not output
according to the format of the source.
In this case, in the Blu-ray Disc Player settings
try setting "BD video supplementary sound" (or
secondary sound) to "Off".
Change the listening mode after changing the setting
to confirm.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR444 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR444 in the language / languages: English as an attachment in your email.

The manual is 4,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR444

Onkyo TX-SR444 User Manual - English - 218 pages

Onkyo TX-SR444 User Manual - German - 228 pages

Onkyo TX-SR444 User Manual - German - 100 pages

Onkyo TX-SR444 User Manual - Dutch - 225 pages

Onkyo TX-SR444 User Manual - Dutch - 100 pages

Onkyo TX-SR444 User Manual - French - 40 pages

Onkyo TX-SR444 User Manual - Italian, Swedish - 100 pages

Onkyo TX-SR444 User Manual - Spanish - 40 pages

Onkyo TX-SR444 User Manual - Finnish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info