492645
46
Zoom out
Zoom in
Previous page
1/68
Next page
Advanced Operations
En-46
Audio Return Ch (ARC)
` Off
` Auto:
The audio signal from your TV tuner can be sent to
the HDMI OUT of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to the HDMI OUT of
the AV receiver. To use this function, you must select the
TV/CD input selector and your TV must be ARC capable.
Note
This setting is fixed to “----” when the “HDMI Ctrl (RIHD)
setting is set to “Off”.
This setting is set to “Auto” automatically when the “HDMI Ctrl
(RIHD)” setting is set to “On” for the first time.
If you set “Audio Return Ch” to “Auto”, the “Audio Selector
settings of the TV/CD input selector will be automatically
switched to “ARC” ( page 43).
LipSync
` Off
` On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
You can change various audio settings from the Home
menu ( page 33).
Note
These settings are not available in either of the following cases:
–TheAudio TV Out” setting is set to “On” ( page 45).
–“HDMI Ctrl (RIHD)” is set to “On” ( page 45) and you’re
listening through your TV speakers.
Tone Control
Bass
` –10 dB to 0dB
to +10 dB in 2 dB steps
You can boost or cut low-frequency sounds output
from the front speakers.
Treble
` –10 dB to 0dB
to +10 dB in 2 dB steps
You can boost or cut high-frequency sounds output
from the front speakers.
You can adjust the bass and treble for Speakers A and B
front speakers, except when the Direct listening mode is
selected.
Operating on the remote controller directly
Tip
Alternatively, you can use the AV receiver’s TONE and /+.
Speaker Levels
Subwoofer Level
` –15 dB to 0dB
to +12 dB in 1 dB steps
Center Level
` –12 dB to 0dB to +12 dB in 1 dB steps
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to standby. To save the setting you made
here, go to “Level Cal (Level Calibration)” ( page 41)
before setting the AV receiver to standby.
Note
These settings cannot be calibrated in either of the following
cases:
A pair of headphones is connected.
The AV receiver is muted.
Speakers that are set to “No” or “None” in the “Sp Config
(Speaker Configuration)” ( page 40) cannot be adjusted.
After changing the settings of the HDMI Ctrl
(RIHD), HDMI Through or Audio Return Ch
turn off the power on all connected pieces of equipment
and then turn them on again. Refer to the user’s manuals
for all connected pieces of equipment.
Using the Audio Settings
1
Press RECEIVER followed by HOME.
2
Use q/w and ENTER to select “Audio”, and then
use q/w/e/r to make the desired selection.
1
Press RECEIVER once followed by TONE
repeatedly to select either “Bass” or “Treble”.
2
Use and + to adjust.
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR313 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR313 in the language / languages: English as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR313

Onkyo TX-SR313 Quick start guide - English - 4 pages

Onkyo TX-SR313 Quick start guide - German - 4 pages

Onkyo TX-SR313 User Manual - German - 68 pages

Onkyo TX-SR313 Quick start guide - Dutch - 4 pages

Onkyo TX-SR313 User Manual - Dutch - 68 pages

Onkyo TX-SR313 Quick start guide - French - 4 pages

Onkyo TX-SR313 User Manual - French - 68 pages

Onkyo TX-SR313 Quick start guide - Italian - 4 pages

Onkyo TX-SR313 User Manual - Italian - 68 pages

Onkyo TX-SR313 Quick start guide - Swedish - 4 pages

Onkyo TX-SR313 User Manual - Swedish - 68 pages

Onkyo TX-SR313 Quick start guide - Spanish - 4 pages

Onkyo TX-SR313 User Manual - Spanish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info