645326
69
Zoom out
Zoom in
Previous page
1/72
Next page
69
Troubleshooting—Continued
The subwoofer produces no sound
The subwoofer outputs no sound while only speaker
set B is on. Turn on speaker set A.
If the source material contains no audio in the LFE
channel, the subwoofer produces no sound.
Check the “3. Sp Config” (page 54).
On the AV receiver, the subwoofer setting in the “3. Sp
Config” is set to “No”. Set the subwoofer setting to
“Yes”.
There’s no sound with a certain signal format
Check the digital audio output setting on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
With some DVD-Video discs, you need to select an
audio format from a menu or with the [AUDIO] button
on your DVD player’s remote controller.
Can’t get 5.1-channel playback
When speaker B is turned on, speaker set A is reduced
to 2.1-channel playback.
The volume cannot be set to 79
After the Audyssey 2EQ™ Room Correction and
Speaker Setup function has been run, or the volume
level of each individual speaker has been adjusted
(pages 33 and 56), the maximum volume may be
reduced.
When the levels of each speaker have been adjusted
(page 56), the maximum possible volume may be
reduced.
Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and so on can degrade audio
performance, so don’t use them.
An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesn’t work
Make sure that the source is Dolby Digital (page 60).
About DTS signals
When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a
malfunction.
When DTS program material ends and the DTS
bitstream stops, the AV receiver remains in DTS
listening mode and the DTS indicator remains on.
This is to prevent noise when you use the pause, fast
forward, or fast reverse function on your player. If you
switch your player from DTS to PCM, as the AV
receiver does not switch formats immediately, you
may not hear anything, in which case you should stop
your player for about 3 seconds, and then resume
playback.
With some CD players, you won’t be able to playback
DTS material properly even though your player is
connected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency
response changed) and the AV receiver doesn’t
recognize it as a genuine DTS signal. In such cases,
you may hear noise.
There’s no picture
Make sure that all video connecting plugs are pushed
in all the way (page 18).
Make sure that each video component is properly
connected.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
The AV receiver does not convert between formats, so
if a video source component is connected to a
component video input, your TV must be connected to
the component video output (page 19).
If the video source is connected to an HDMI input,
your TV must be connected to the HDMI OUT
(page 19).
There’s no picture from a source connected to
an HDMI IN
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not supported (page 21).
If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that your TV does not
support the current video resolution and you need to
select another resolution on your DVD/BD player.
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
light up
Relocate your antenna.
Move the AV receiver away from your TV or
computer.
Listen to the station in mono (page 43).
When listening to an AM station, operating the remote
controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
Make sure that the batteries are installed with the
correct polarity (page 12).
Install new batteries. Don’t mix different types of bat-
teries, or old and new batteries (page 12).
Make sure that the remote controller is not too far
away from the AV receiver and there’s no obstruction
between the remote controller and the AV receiver’s
remote control sensor (page 12).
Video
Tuner
Remote Controller
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR307 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR307 in the language / languages: English as an attachment in your email.

The manual is 7,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR307

Onkyo TX-SR307 User Manual - German - 144 pages

Onkyo TX-SR307 User Manual - Dutch - 144 pages

Onkyo TX-SR307 User Manual - French - 144 pages

Onkyo TX-SR307 User Manual - Italian - 144 pages

Onkyo TX-SR307 User Manual - Swedish - 144 pages

Onkyo TX-SR307 User Manual - Spanish - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info