601862

Onkyo TX-RZ900 Manual

13
Zoom out
Zoom in
Previous page
1/142
Next page
Step 2:
Initial Setup
Step 2:
Initial Setup
En-13
＊ Correct measurement will not be possible if the microphone is held
by hand. Measurement is not possible if headphones are being used.
＊ The subwoofer sound may not be detected since it is extremely
low frequencies. Set the subwoofer volume to around the half of its
maximum volume.
＊ Measurement may be interrupted if there is ambient noise or radio
frequency interference. If this occurs, close the window and turn off
the home appliance and fluorescent light.
2. After placing the microphone at the measurement
position, select "Do it Now" with the cursors and
press ENTER.
3. When "Please plug microphone that came in a
box with AV receiver" is displayed, connect the
microphone to the SETUP MIC jack of the unit.
SETUP MIC jack
Calibration
microphone
4. Set the speakers you have connected and the type
of Height Speakers.
AccuEQ Room Calibration
Speaker Channels
Subwoofer
Height Speaker
Bi-Amp
Powered Zone2
7.1ch
Yes
-----
No
No
Next
ENTER
Select how many speakers you have.
When the screen above is displayed, set the items with
the cursors on the remote controller. The image on the
screen changes as you choose the number of channels
in "Speaker Channels", so refer to it when performing
the settings. After completing all the settings, press
ENTER on the remote controller.
After this, follow the guidance displayed on the TV screen.
･ When the cursor is on an item, the content of the item
will be shown in the lower part of the screen.
5. The test tones sound from the connected speakers
and automatic speaker setting starts.
Measurement will be made three or more times for each
speaker. It takes several minutes to be completed. Keep
the room as quiet as possible during measurement. If
any of the speakers do not produce the test tone, check
for disconnection.
･ During measurement, each speaker outputs the test
tones at a high volume. Be careful of sound leak
that may disturb your neighbors, or be careful not to
frighten young children.
6. When the measurement is completed, the
measurement result is displayed.
Press
t
/
u
on the remote controller to check the
settings. Press ENTER with "Save" selected. To have
the settings reflected for all the speakers, select "On (All
Channels)" in the next screen and press ENTER on the
remote controller.
･ Select "On (Except Front Left / Right)" to disable just
the front speakers.
･ If there is an error message, follow the on-screen
instruction to remove the error cause. If the
subwoofer was not detected, turn the volume of the
subwoofer up to maximum and then select "Retry".
About THX playback
THX recommends setting the speakers manually if
you use THX-certified speakers or playing back with
THX listening modes.
･ THX recommends setting the crossover frequency
to "80Hz(THX)" manually.
･ Due to the electrical complexities and the
interaction with the room, you may notice irregular
results when setting the level or distance of each
speaker. If this happens, THX recommends
setting the speakers and the subwoofer manually.
7. When "Please unplug setup microphone." is
displayed, disconnect the microphone.
2
Source Connection
You can check the connections for each of the inputs and
configure the HDMI link function.
1. When the Source Connection start screen is
displayed, select "Yes, Continue" with the cursors
and press ENTER.
Source Connection
This step will start to check if the
co nnections were made correctly.
Wo uld you like to continue?
Yes. Continue
No. Skip
Initial Setup
Exit
SETUP
2. Select the desired input to check the connection and
press ENTER.
Start playback of the selected device. If connection is
correct, video/audio of the input source selected on the
unit will be played.
3. After checking the connection, select "Yes" with the
cursors and press ENTER.
･ If you select "No" and press ENTER, the error cause
will be displayed. Follow the guidance to remove the
error cause and check the connection again.
4. Select "Yes" with the cursors and press ENTER
on the remote controller to check the connection
of other inputs or select "No, Done Checking" and
press ENTER to skip.
If you select "Yes", you will return to the screen of step
2.
If you select "No, Done Checking", you will proceed to
step 5.
5. Settings for the CEC link function.
To enable the HDMI link function with CEC compatible
equipment, select "Yes", then select "Yes" again in the
next screen.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-RZ900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-RZ900 in the language / languages: English as an attachment in your email.

The manual is 5,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-RZ900

Onkyo TX-RZ900 User Manual - German, Dutch - 140 pages

Onkyo TX-RZ900 User Manual - French - 56 pages

Onkyo TX-RZ900 User Manual - Italian, Swedish - 140 pages

Onkyo TX-RZ900 User Manual - Spanish - 56 pages

Onkyo TX-RZ900 User Manual - Finnish - 140 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info