645296
26
Zoom out
Zoom in
Previous page
1/105
Next page
26
> Before start > Hookup > Setup >Playback > Part Names > Advanced Manual
Troubleshooting | Appendix
0 If ZONE 2 or ZONE 3 is turned on when the listening
mode of the main room is Pure Audio, it will
automatically switch to the Direct listening mode.
4. To adjust the volume on the power amplifier in the
separate room or the ZONE 2 SPEAKER, adjust with
VOL+/– on the remote controller. To control on the main
unit, press ZONE 2 or ZONE 3 and adjust with the
MASTER VOLUME control within 8 seconds.
0
The information for a connected device can be displayed on the
TV screen in a separate room. Press the button while the
remote controller is in the mode for controlling ZONE 2.
0 Power consumption in standby mode increases when the
multi-zone function is being used.
To turn off the function
Press Í while in the mode for controlling ZONE 2 or ZONE
3 on the remote controller.
Playing in ZONE 2 or ZONE 3 only
If you turn the unit to standby during multi-zone playback,
the Z2 or Z3 indicator is dimmed and the playback mode is
switched to playback in a separate room only. Setting
ZONE 2/ZONE 3 to on while this unit is in standby will also
switch the playback mode to the same setting.
WHOLE HOUSE MODE
If you press WHOLE HOUSE MODE while playback is
being performed in the main room, the WHOLE HOUSE
MODE is turned on, "Z2" and "Z3" on the display light at the
same time and the playback sources of all the rooms are
switched to the same source at once.
0
The sources that can be played in ZONE 2 can be played in all rooms.
0 This function cannot be used if headphones are
connected or audio is output from the speakers of the TV.
Settings
Settings are required in Initial Setup, "4. Multi Zone Setup"
(
P21) to use the multi-zone feature. When checking the
setting content, refer to the following, press on the remote
controller, and check in the Setup menu that is displayed.
– When you have connected a TV in the separate room
with an HDMI cable, have you selected "Use" in "1. Input
/Output Assign" – "TV Out/OSD" – "Zone2 HDMII"?
When you are playing the audio from an AV component in the
separate
room
connected with an HDMI cable, have you selected
"Use" in "1. Input /Output Assign" – "TV Out/OSD" – "Zone2 HDMI"?
When you have connected speakers in a separate room
with speaker cable, have you selected "Zone 2" (or "Zone 2
A + B") in "2. Speaker" – "Configuration" – "Zone Speaker"?
When you have connected a power amplifier in a separate
room with an analog audio cable and you want to control the
volume with this unit, have you selected "Variable" in "
6.
Multi Zone
" – "Zone 2" or "Zone 3" – "Output Level"?
Others
To adjust the sound quality
It is possible to enhance or moderate the bass and treble of
front speakers. Press TONE on the main unit several times
to select the desired setting from "Bass" and "Treble", and
turn the TONE dial to adjust.
0 You can also adjust the sound quality of a power
amplifier connected in a separate room. After pressing
either ZONE 2 or ZONE 3 on the main unit, within
8 seconds press TONE and turn the TONE dial to adjust.
0
This cannot be set if the listening mode is Pure Audio or Direct.
Quick Menu
By pressing Q on the remote controller during play, you can
adjust frequently used settings, such as the sound quality,
using on-screen menus. Select the item with the cursors of
the remote controller and press ENTER to confirm your
selection. To return to the previous screen, press .
"Tone": It is possible to enhance or moderate the bass and
treble of front speakers.
"Other": Enables you to make a variety of settings.
0 "Speaker Layout": You can switch the output on the
surround back speakers and height speakers.
0 "A/V Sync": If the video is behind the audio, you can
delay the audio to offset the gap.
0 "Music Optimizer": Improve the quality of compressed
audio.
0 "HDMI Out": Allows you to select the HDMI OUT jack to
output video signals from "MAIN", "SUB", and
"MAIN+SUB".
When the unit is operating erratically
Try restarting the unit
Restarting the unit may help it operate more smoothly. To
restart the unit, turn it to standby, and then press Í ON/
STANDBY on the main unit for at least 5 seconds. (The
unit’s settings will be maintained.) If there is no
improvement even after the unit is restarted, try
disconnecting and reconnecting the power cords of the unit
and connected equipment.
Resetting the unit (this resets the unit settings to the
default)
If restarting the unit doesn't fix the problem, resetting the
unit to the status at the time of shipment may solve the
problem. If you reset the unit status, your preferences will
be reset to the defaults. Note them down before the
operation below.
1. While pressing the CBL input selector button on the main
unit, press Í ON/STANDBY.
2. "Clear" appears on the display and the unit returns to
standby. Do not unplug the power cord until "Clear"
disappears from the display.
To reset the remote controller, while holding down MODE,
press until the remote indicator flash twice (about
3 seconds).
Quick Menu
Tone
Level
AccuEQ
Other
Bass
Treble
BD/DVD
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-RZ810 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-RZ810 in the language / languages: English as an attachment in your email.

The manual is 4,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-RZ810

Onkyo TX-RZ810 User Manual - German, Dutch - 164 pages

Onkyo TX-RZ810 User Manual - French - 68 pages

Onkyo TX-RZ810 User Manual - Italian, Swedish - 164 pages

Onkyo TX-RZ810 User Manual - Spanish - 68 pages

Onkyo TX-RZ810 User Manual - Finnish - 164 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info