601863
97
Zoom out
Zoom in
Previous page
1/142
Next page
Connecting and Operating Onkyo RI Components
En-61
Connecting and Operating
Onkyo RI Components
About RI Function
Connecting an Onkyo component with RI jack such as
the separately sold RI Dock to the unit by using an RI
cable and an analog audio cable enables the following RI
functions:
System On / Auto Power On: Starting playback on a
component connected via RI when the unit is on standby
mode, automatically turns on the unit to select the relevant
component as its input source.
Direct Change: When playback is started on a component
connected via RI, the unit selects that component as the
input source.
Remote Controller Operation: Allows you to operate
RI-compatible Onkyo components using the AV receiver's
remote controller. Point the remote controller at remote
control sensor of the unit. This operation is possible only
when the RI remote control code is programmed.
Some components may not support all RI functions.
These functions do not work when Zone 2/Zone 3 is
turned on.
For information on the RI functions, also refer to each
component's instruction manual.
RI Connection and Setting
R
L
Connect an Onkyo component with RI jack to this unit using
an RI cable and an analog audio cable. For details, refer
to the instruction manual of the component with RI jack.
The RI cable can be connected in any order. When there
are two RI jacks, both jacks work in the same way and are
interchangeable.
To connect the RI Dock or cassette tape deck via RI, the
following settings are required.
Rename the input selector
To make the RI functions work, you must rename the input
selectors on the unit. Press CD or G1 on the main unit to
display "CD" or "GAME1" on the main unit display. Then
press and hold CD or G1 on the main unit 3 seconds or
more to switch the display to "DOCK" or "TAPE".
To program the RI remote control code
Program the remote control code to any REMOTE MODE
button on the remote controller. This will allow you to
operate the component by pointing the remote controller at
the unit instead of the component.
1. Press and hold DISPLAY for 3 or more seconds while
holding down the REMOTE MODE button to which you
want to program the remote control code.
The remote indicator will light.
The RCV, ZONE2 and ZONE3 buttons cannot be
programmed.
2. With the number buttons, enter the following 5-digit
remote control code within 30 seconds.
RI Dock: 81993
Cassette tape deck with RI jack: 42157
Programming is complete when the remote indicator
flashes twice. The remote indicator flashes once
slowly when programming the remote control code
fails. Try programming again.
Input selector on the RI Dock: Switch to "DOCK" or
"TAPE". For details, refer to the RI Dock's instruction
manual.
To operate Onkyo components directly or Onkyo
components that are not connected via RI, use the
following remote control codes:
Onkyo DVD player: 30627
Onkyo CD player: 71817
RI Dock: 82990
With some models, operation may be not possible in
part or not possible at all.
97


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-RZ800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-RZ800 in the language / languages: English as an attachment in your email.

The manual is 5,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-RZ800

Onkyo TX-RZ800 User Manual - German, Dutch - 140 pages

Onkyo TX-RZ800 User Manual - French - 56 pages

Onkyo TX-RZ800 User Manual - Italian, Swedish - 140 pages

Onkyo TX-RZ800 User Manual - Spanish - 56 pages

Onkyo TX-RZ800 User Manual - Finnish - 140 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info