645298
55
Zoom out
Zoom in
Previous page
1/99
Next page
23
> Specifications > Settings > Listening Modes > Playback Function > Basic Manual
Troubleshooting | Appendix
Initial Setup
When you turn the unit on for the first time after purchasing
it, Initial Setup is automatically shown on the TV to enable
you to make settings required for startup using simple
operations following onscreen guidance.
English
Deutsch
Français
Español
Italiano
Nederlands
Svenska
Exit
Initial Setup
Language Select
Operation:
Select the item with the cursors of the remote controller
and press ENTER to confirm your selection. To return to
the previous screen, press
.
To redo Initial Setup:
If you terminate the procedure on the way or want to
change a setting made during Initial Setup, press
on the
remote controller, select "7. Miscellaneous" - "Initial Setup",
and press ENTER.
1� AccuEQ Room Calibration
Place the supplied speaker setup microphone in the
listening position, measure the test tones emitted by the
speakers, then the unit automatically sets the optimum
volume level for each speaker, the crossover frequencies,
and the distance from the listening position. This also
automatically adjusts the equalizers for the speakers and
enables correction of distortion caused by the acoustic
environment of the room.
Calibration takes several minutes to be completed.
The speakers emit the test tone at high volume during
measurement, so be careful of your surroundings. Keep
the room as quiet as possible during measurement. If
the measurement is interrupted, turn off the household
appliances.
When using THX certified speakers, THX recommends
setting the crossover frequency to "80Hz(THX)". It is
also recommended to manually adjust the settings for
each speaker to suit the specific characteristics of each
room.
1. Place the supplied speaker setup microphone in the
listening position, and connect to the SETUP MIC jack
on the main unit.
SETUP MI
C
When putting the speaker setup microphone on a
tripod, refer to the illustration when putting it in place.
2. Select the connected speaker configuration.
AccuEQ Room Calibration
Speaker Channels
Subwoofer
Height Speaker
Zone Speaker
Bi-Amp
Select how many speakers you have.
Next
7.1 ch
< >
Yes
---
No
No
The image on the screen changes as you choose the
number of channels in "Speaker Channels", so refer to it
when performing the settings. Select 5.1.2ch, etc., when
using a height speaker.
Also use this screen to select whether you have
connected a subwoofer and to select the type of height
speaker, etc.
If you have connected a subwoofer, check the power
and volume of the subwoofer. The low frequencies
played by the subwoofer may not be discernible, so
set its volume to at least halfway.
3. Test tones are emitted by the speakers, and firstly the
unit detects the speakers connected and the noise in
the environment.
4. After the results of the above measurements are
displayed, select "Next", press ENTER on the remote
controller, and the test tones are emitted again, and the
unit automatically makes settings such as the optimum
volume level and the crossover frequency.
5. When the measurement is completed, the measurement
result is displayed.
Press the cursors
/
on the remote controller to
check the settings. Press ENTER when "Save" is
selected to save the settings.
AccuEQ Room Calibration
Subwoofer
Front
Center
Surround
Surround Back
Height
Review Crossover
: Yes
: 80Hz(THX)
: 80Hz(THX)
: 80Hz(THX)
: 80Hz(THX)
: ---
Save
Cancel
6. Select whether to enable or disable the equalizer
function that corrects for distortion caused by the
acoustic environment of the room.
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-RZ710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-RZ710 in the language / languages: English as an attachment in your email.

The manual is 4,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-RZ710

Onkyo TX-RZ710 User Manual - German, Dutch - 160 pages

Onkyo TX-RZ710 User Manual - French - 64 pages

Onkyo TX-RZ710 User Manual - Italian, Swedish - 160 pages

Onkyo TX-RZ710 User Manual - Spanish - 64 pages

Onkyo TX-RZ710 User Manual - Finnish - 160 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info