517568
30
Zoom out
Zoom in
Previous page
1/160
Next page
Turning On & Basic Operations
En-30
Note
You can cancel Audyssey MultEQ XT32 Room Correction
and Speaker Setup at any point in this procedure simply by
disconnecting the setup microphone.
Do not connect or disconnect any speakers during
Audyssey MultEQ XT32 Room Correction and Speaker
Setup.
If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ XT32 Room Correction and
Speaker Setup starts.
Changes to the room after Audyssey MultEQ XT32 Room
Correction and Speaker Setup requires you run
Audyssey MultEQ XT32 Room Correction and Speaker
Setup again, as room EQ characteristics may have
changed.
Error Messages
While Audyssey MultEQ XT32 Room Correction and
Speaker Setup is in progress, one of the error
messages below may appear.
The options are:
` Retry:
Try again.
` Cancel:
Cancel Audyssey MultEQ XT32 Room
Correction and Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the
source of the noise and try again.
• Speaker Matching Error!
The number of speakers detected was different
from that of the first measurement. Check the
speaker connection.
• Writing Error!
This message appears if saving fails. Try saving
again. If this message appears after 2 or 3
attempts, contact your Onkyo dealer.
• Speaker Detect Error
This message appears if a speaker is not detected.
No” means that no speaker was detected.
Tip
See “Speaker Configuration” for appropriate settings
( page 14).
Note
Please note that THX recommends any THX main
speakers be set to “80Hz(THX)”. If you set up your
speakers using Audyssey MultEQ XT32 Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to “80Hz(THX)” crossover
( page 65).
Sometimes due to the electrical complexities of subwoofers
and the interaction with the room, THX recommends setting
the level and the distance of the subwoofer manually.
Sometimes due to interaction with the room, you may
notice irregular results when setting the level and/or
distance of the main speakers. If this happens, THX
recommends setting them manually.
Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs
very low-frequency sound at a low volume level, it
may not be detected by Audyssey MultEQ XT32
Room Correction and Speaker Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the
subwoofer’s volume to the half-way point, set it to its
highest crossover frequency, and then try running
Audyssey MultEQ XT32 Room Correction and
Speaker Setup again. Note that if the volume is set
too high and the sound distorts, detection issues may
occur, so use an appropriate volume level. If the
subwoofer has a low-pass filter switch, set it to Off or
Direct. Refer to your subwoofer’s instruction manual
for details.
10
Use q/w to select a target, and use e/r to
change the setting.
After the results of Audyssey MultEQ
®
XT32
have been saved, the menu will display the
“Audyssey” ( page 71), “Dynamic EQ”
( page 72), “Dynamic Volume” ( page 72)
settings.
Note
When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
These settings are applied to all input selectors.
11
Press ENTER.
12
Disconnect the speaker setup microphone.
Retry
Cancel
Ambient noise is too high.
AUDYSSEY
MultEQ XT32: Auto Setup
Error message
The setup of the speaker can be done manually
( page 65).
The setup of the volume level of each speaker also
can be done manually ( pages 66, 67).
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR929 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR929 in the language / languages: English as an attachment in your email.

The manual is 4,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR929

Onkyo TX-NR929 Quick start guide - English - 4 pages

Onkyo TX-NR929 Quick start guide - German - 4 pages

Onkyo TX-NR929 User Manual - German - 160 pages

Onkyo TX-NR929 Quick start guide - Dutch - 4 pages

Onkyo TX-NR929 User Manual - Dutch - 160 pages

Onkyo TX-NR929 User Manual - French - 160 pages

Onkyo TX-NR929 User Manual - French - 4 pages

Onkyo TX-NR929 User Manual - Italian - 156 pages

Onkyo TX-NR929 Quick start guide - Italian - 4 pages

Onkyo TX-NR929 User Manual - Swedish - 160 pages

Onkyo TX-NR929 Quick start guide - Swedish - 4 pages

Onkyo TX-NR929 User Manual - Spanish - 160 pages

Onkyo TX-NR929 Quick start guide - Spanish - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info