62439
72
Zoom out
Zoom in
Previous page
1/150
Next page
72
Basic Operations—Continued
With the sleep timer, you can set the AV receiver to turn
off automatically after a specified period.
If you need to cancel the sleep timer, press the [SLEEP]
button repeatedly until the SLEEP indicator disappears.
To check the time remaining until the AV receiver sleeps,
press the [
SLEEP
] button. Note that if you press the
[
SLEEP
] button while the sleep time is being displayed,
you’ll shorten the sleep time by 10 minutes.
For private listening, you can connect a pair of stereo
headphones (1/4-inch phone plug) to the AV receiver’s
PHONES jack.
Notes:
Always turn down the volume before connecting your
headphones.
While the headphones plug is inserted in the PHONES
jack, the speakers are turned off and the Headphone
indicator lights up. (The Powered Zone 2 speakers are
not turned off.)
When you connect a pair of headphones, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio.
Only the Stereo, Direct, Pure Audio, and Mono listen-
ing modes can be used with headphones (the listening
modes available also depend on the currently selected
input source).
When the multichannel input is used, only the front
left and right audio can be heard in the headphones.
You can adjust the bass and treble for the front speakers,
except when the Direct, Pure Audio or THX listening
mode is selected.
Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 1 dB steps.
Treble
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10dB in 1dB steps.
Notes:
This setting is not available when the multichannel
Analog input is selected.
The tone can be adjusted for Speakers A or Speakers
B. The same values are used for both.
The tone control settings do not apply to the Direct,
Pure Audio, or THX listening modes.
You can display various information about the current
input source as follows.
The following information can typically be displayed:
* If the input signal is analog, no format information is displayed.
If the input signal is PCM, the sampling frequency is displayed.
If the input signal is digital but not PCM, the signal format and
the number of channels is displayed. For some digital input sig-
nals, including multichannel PCM, the signal format, number of
channels, and sampling frequency is displayed.
Information is displayed for about three seconds, then the previ-
ously displayed information reappears.
Using the Sleep Timer
Press the [RECEIVER] button,
and then press the [SLEEP] but-
ton repeatedly to select the
required sleep time.
The sleep time can be set from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set. The specified sleep time appears on
the display for about five seconds, then
the previous display reappears.
Using Headphones
Adjusting the Bass & Treble
1
Press the AV receivers [TONE]
button repeatedly to select Bass
or Treble for Front, Center, Sur-
round, SurrBack, or Subwoofer.
2
Use the Up [r] and Down [e]
buttons to adjust.
Displaying Source Information
Remote
controller
AV receiver
Press the [DISPLAY] button
repeatedly to cycle through the
available information.
Input source
Listening
mode
Signal format*
Sampling
frequency
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR906 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR906 in the language / languages: English as an attachment in your email.

The manual is 7,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR906

Onkyo TX-NR906 User Manual - German - 294 pages

Onkyo TX-NR906 User Manual - Dutch - 294 pages

Onkyo TX-NR906 User Manual - Italian - 294 pages

Onkyo TX-NR906 User Manual - Swedish - 294 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info