549875
8
Zoom out
Zoom in
Previous page
1/114
Next page
8
Punto 2:
Impostazione
2.
Dopo aver posizionato il microfono nella posizione
di misurazione, selezionare “Do it Now” con i cursori
e premere ENTER.
3.
Collegare il microfono al jack SETUP MIC dell’unità.
Jack SETUP MIC
Microfono per
l’impostazione
del diffusore
4.
Seguire le indicazioni visualizzate sullo schermo del
televisore.
AccuEQ Room Calibration
Front Speakers Type
Powered Zone 2
Subwoofer
Normal
No
Yes
Set bi-amp only if you use 2 channel amp for each front speaker.
ENTER Nex t
Quando è visualizzata la schermata precedente,
impostare le voci con i cursori sul telecomando. Quando
il cursore si trova su una voce, il contenuto della voce
verrà mostrato in basso a sinistra della schermata. Dopo
aver impostato le voci, premere ENTER sul telecomando.
Premere ENTER anche nella schermata successiva.
5.
Il suono di prova è udibile dai diffusore collegati e si
avvia l’impostazione automatica del diffusore.
La misurazione sarà effettuata due volte per ciascun diffusore.
Saranno necessari diversi minuti per il completamento.
Tenere la stanza quanto più silenziosa possibile durante la
misurazione. Se uno dei diffusori non produce il suono di
prova, controllare l’eventuale scollegamento.
6.
Al termine della misurazione, verrà visualizzato il
risultato della stessa.
Premere
W
/
X
sul telecomando per controllare le
impostazioni. Premere ENTER con “Save” selezionato.
Nella schermata successiva, che mostra che “AccuEQ”
è “On”, premere ENTER sul telecomando.
r Se compare un messaggio di errore, seguire le istruzioni
sullo schermo per eliminare la causa dell’errore.
Informazioni circa la riproduzione THX
THX consiglia di impostare gli altoparlanti
manualmente se si utilizzano altoparlanti certificati
THX o se si riproduce con modalità di ascolto THX.
r
THX consiglia di impostare la frequenza di crossover
su “80Hz (THX)” manualmente.
r A causa delle complessità elettriche e dell'interazione
con la stanza, è possibile notare risultati irregolari
quando si imposta il livello o la distanza di ciascun
altoparlante. In tal caso, THX consiglia di impostare
gli altoparlanti e il subwoofer manualmente.
7.
Quando viene visualizzato “Please unplug setup
microphone., scollegare il microfono.
2nd Step : Source Connection
Si può controllare se ciascuna sorgente di ingresso sia
collegata correttamente o meno.
1.
Quando è visualizzata la schermata di avvio
Collegamento sorgente, selezionare “Yes, Continue”
con i cursori e premere ENTER.
This step will start to check if the
connections were made correctly.
Would you like to continue?
Yes. Continue
No. Skip
Initial Setup
Source Connection
ExitHOME
2.
Selezionare l’ingresso desiderato per controllare il
collegamento e premere ENTER.
Avviare la riproduzione del dispositivo selezionato. Se il
collegamento è corretto, il video/audio della sorgente di
ingresso selezionata sull’unità verrà riprodotto.
3.
Dopo aver controllato il collegamento, selezionare
“Yes” con i cursori e premere ENTER.
r Se si seleziona “No” e si preme ENTER, verrà
visualizzata la causa dell’errore. Seguire la guida per
eliminare la causa dell’errore e controllare di nuovo il
collegamento.
4.
Selezionare “Yes” con i cursori e premere ENTER
sul telecomando per controllare il collegamento di
altri ingressi o selezionare “No, Done Checking” e
premere ENTER per saltare.
Se si seleziona “Yes”, si torna alla schermata del punto 2.
Se si seleziona “No, Done Checking”, si procederà al punto 5.
5.
Abilitazione delle operazioni collegate via HDMI e di
altre funzioni
Nella schermata successiva, è possibile abilitare il
funzionamento collegato via HDMI con dispositivo
compatibile CEC, il collegamento con televisore
compatibile ARC e la funzione HDMI Through. Selezionare
“Yes” con i cursori per abilitarle o “No, Done Checking” per
saltarle, quindi premere ENTER sul telecomando.
6.
Selezionare “Yes” con i cursori e premere ENTER per
abilitare la funzione di collegamento CEC o selezionare
“No” e premere ENTER per mantenerla disattivata.
The following CEC-compatible devices are found;
Do you wish to turn on the CEC link?
Integra DHS-8.8
Yes
No
Source Connection
ExitHOME
Se si seleziona “Yes”, il collegamento con il televisore
compatibile ARC e la funzione HDMI Through saranno
impostati su “Auto” e abilitati.
3rd Step : Remote Mode Setup
In questo passaggio, è possibile abilitare il funzionamento
degli altri componenti tramite il telecomando dell’unità.
Quando è visualizzata la schermata di avvio configurazione
modalità remota, selezionare “Yes” con i cursori e premere
ENTER sul telecomando. Seguire la guida per selezionare
il pulsante REMOTE MODE desiderato e, nella schermata
della tastiera, immettere i primi tre caratteri del marchio del
dispositivo che verrà programmato (es., “ONK” per ONKYO)
e cercare il codice telecomando. La guida spiegherà anche
come impostare il telecomando.
HOME Ex it
Initial Setup
Remote Mode Setup
Preprograming remote will give you control
of other devices from AV receiver remote
Would you like to setup your remote to
control your devices? This may take a while
depending on what and how many you have
connected. You can always come back to remote
setup from setup “8-2 Remote Mode Setup”.
Yes
No. Skip
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR838 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR838 in the language / languages: Italian as an attachment in your email.

The manual is 6,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR838

Onkyo TX-NR838 User Manual - English - 94 pages

Onkyo TX-NR838 User Manual - English - 20 pages

Onkyo TX-NR838 User Manual - German - 122 pages

Onkyo TX-NR838 User Manual - German - 278 pages

Onkyo TX-NR838 User Manual - Dutch - 122 pages

Onkyo TX-NR838 User Manual - Dutch - 274 pages

Onkyo TX-NR838 User Manual - French - 46 pages

Onkyo TX-NR838 User Manual - Italian, Swedish - 122 pages

Onkyo TX-NR838 User Manual - Spanish - 46 pages

Onkyo TX-NR838 User Manual - Finnish - 122 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info