527521
92
Zoom out
Zoom in
Previous page
1/152
Next page
Appendix
En-92
Only the front speakers produce sound
Only the center speaker produces sound
The surround speakers produce no sound
The center speaker produces no sound
The front high, front wide and surround back
speakers produce no sound
The subwoofer produces no sound
There’s no sound with a certain signal format
Can’t select the Pure Audio listening mode
Can’t get 6.1/7.1 playback
The speaker volume cannot be set as required
Noise can be heard
The Late Night function doesn’t work
About DTS signals
If the input signal format is set to “PCM” or “DTS”. Set it to
Off”. ( page 72)
When the Stereo or Mono listening mode is selected, only
the front speakers and subwoofer produce sound.
( page 46)
In the Mono listening mode, only the front speakers output
sound if the “Output Speaker” setting is set toLeft /
Right”. ( page 67)
Make sure the speakers are configured correctly.
( page 63)
If you use the Dolby Pro Logic IIx Movie, Dolby Pro Logic
IIx Music, or Dolby Pro Logic IIx Game listening mode with
a mono source, such as an AM radio station or mono TV
program, the sound is concentrated in the center speaker.
In the Mono listening mode, only the center speaker output
sound if the “Output Speaker” setting is set toCenter”.
( page 67)
Make sure the speakers are configured correctly.
( page 63)
When the T-D (Theater-Dimensional), Stereo or Mono
listening mode is selected, the surround speakers produce
no sound.
Depending on the source and current listening mode, not
much sound may be produced by the surround speakers.
Try selecting another listening mode. ( page 44)
Make sure the speakers are configured correctly.
( page 63)
When the Stereo or Mono listening mode is selected, the
center speaker produces no sound.
In the Mono listening mode, only the front speakers output
sound if the “Output Speaker” setting is set toLeft /
Right”. ( page 67)
Make sure the speakers are configured correctly.
( page 63)
Depending on the current listening mode, no sound may be
produced by the front high, front wide and surround back
speakers. Select another listening mode. ( page 44)
Depending on the sources, the sound produced by the
front high, front wide and surround back speakers may be
weak.
Make sure the speakers are configured correctly.
( page 64)
When Powered Zone 2 is used, playback in the main room
is reduced to 5.1channels and the front high, front wide and
surround back speakers produce no sound.
When you play source material that contains no information
in the LFE channel, the subwoofer produces no sound.
Make sure the speakers are configured correctly.
( page 63)
Check the digital audio output setting on the connected
device. On some game consoles, such as those that
support DVD, the default setting is off.
With some DVD-Video discs, you need to select an audio
output format from a menu.
Depending on the input signal, some listening modes
cannot be selected. ( pages 44 to 51)
The Pure Audio listening mode cannot be selected while
Zone 2/3 is on.
If no surround back speakers, front wide speakers and
front high speakers are connected, or the Zone 2 speakers
are being used, 6.1/7.1 playback is not possible.
Depending on the number of connected speakers, it is not
always possible to select all of the listening modes.
( pages 44 to 51)
Check to see if a maximum volume has been set.
( page 73)
If the volume level of each individual speaker has been
adjusted to high positive values, then the maximum master
volume possible may be reduced. Note that the individual
speaker volume levels are set automatically after the
Audyssey MultEQ
®
Room Correction and Speaker Setup
has been performed. ( pages 27, 65)
Using cable ties to bundle audio cables with power cords,
speaker cables, and the like may degrade the audio
performance, so refrain from doing it.
An audio cable may be picking up interference. Try
repositioning your cables.
Make sure the source material is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD. ( page 58)
Make sure that the “TrueHD Loudness Management
setting is not set to “Off”. The Late Night function doesn’t
work when this setting is disabled. ( page 68)
When DTS program material ends and the DTS bitstream
stops, the AV receiver remains in DTS listening mode and
the dts indicator remains on. This is to prevent noise when
you use the pause, fast forward, or fast reverse function on
your player. If you switch your player from DTS to PCM,
you may not hear any sound because the AV receiver does
not switch formats immediately. In such case, you should
stop your player for about three seconds and then resume
playback.
With some CD and LD players, you won’t be able to
playback DTS material properly even though your player is
connected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency response
changed) and the AV receiver doesn’t recognize it as a
genuine DTS signal. In such cases, you may hear noise.
Playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may
produce a short audible noise. This is not a malfunction.
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR828 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR828 in the language / languages: English as an attachment in your email.

The manual is 4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR828

Onkyo TX-NR828 Quick start guide - English - 4 pages

Onkyo TX-NR828 Quick start guide - German - 4 pages

Onkyo TX-NR828 User Manual - German - 152 pages

Onkyo TX-NR828 Quick start guide - Dutch - 4 pages

Onkyo TX-NR828 User Manual - Dutch - 152 pages

Onkyo TX-NR828 Quick start guide - French - 4 pages

Onkyo TX-NR828 User Manual - French - 152 pages

Onkyo TX-NR828 Quick start guide - Italian - 4 pages

Onkyo TX-NR828 User Manual - Italian - 152 pages

Onkyo TX-NR828 Quick start guide - Swedish - 4 pages

Onkyo TX-NR828 User Manual - Swedish - 152 pages

Onkyo TX-NR828 Quick start guide - Spanish - 4 pages

Onkyo TX-NR828 User Manual - Spanish - 152 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info