527521
76
Zoom out
Zoom in
Previous page
1/152
Next page
Advanced Operations
En-76
Operating
procedure
( page 60)
Audio Return Channel
` Off
` Auto:
The audio signal from your TV tuner can be sent
to HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an
ARC capable TV to send the audio stream to HDMI
OUT MAIN of the AV receiver. To use this function,
you must select the TV/CD input selector and your TV
must be ARC capable. Default setting: “
-----
Note
This setting is fixed to “-----” when the “HDMI CEC
(RIHD)” setting is set to “Off”.
This setting is set to “Auto” automatically when the “HDMI
CEC (RIHD)” setting is set to “On” for the first time.
If you set “Audio Return Channel” to “Auto”, the “Audio
Selector” settings of the TV/CD input selector will be
automatically switched to “ARC” ( page 72).
Tip
After changing the settings of the “HDMI CEC (RIHD)”,
HDMI Through” or “Audio Return Channel”, turn off the
power on all connected pieces of equipment and then turn
them on again. Refer to the user’s manuals for all
connected pieces of equipment.
Lip Sync
` Off
` On
This function allows the AV receiver to automatically
correct any delay between the video and the audio,
based on the data from the connected monitor.
Note
This function works only if your HDMI-compatible TV
supports HDMI Lip Sync.
InstaPrevue
These settings apply to “InstaPrevue” of the Home
menu
( page 55) and specify the preview display of
HDMI video streams.
Sub Window
` Multi:
Displays preview thumbnails all at once.
` Single:
Displays preview thumbnails one-by-one.
With this setting, you can set the number of preview
thumbnails displayed.
Position
(with “Sub Window” set to “Multi”)
` Top, Bottom
, Left, Right
(with “Sub Window” set to “Single”)
` Upper Left, Upper Right, Lower Left, Lower
Right
With this setting, you can set the position of preview
thumbnails on the TV screen.
Note
Depending on video signals, the picture may not be
properly rendered on the preview thumbnails of
InstaPrevue.
Auto Standby
Auto Standby
` Off
` On
When “Auto Standby” is set to “On”, the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video
signal input.
Auto Standby” will appear on the AV receiver’s
display and OSD 30 seconds before the Auto
Standby comes on.
Default setting: On (European and Australian
models), Off (North American models)
Note
Set to “
On, the Auto Standby function may activate itself
during playback with some sources.
The Auto
Standby function does not work when Zone 2/3 is
on.
HDMI Through
` Off
` On
This setting enables or disables the Auto Standby
during HDMI Through by detecting the audio/video
input signal.
When this setting is set to “On”, the AV receiver will
automatically enter standby mode if there is no audio
and no video signal input during HDMI Through for 30
minutes. (
The Auto Standby function does not work when
Zone 2/3 is on.
)
When this setting is set to “Off”, the status of HDMI
Through is continued regardless of audio/video input
signal.
Tip
Entering standby mode is possible by setting “HDMI CEC
(RIHD)” to “On” and using CEC-compatible component
regardless of the above-mentioned setting.
See “HDMI CEC (RIHD)” in “7. Hardware Setup” for linked
operation ( page 74).
When the HDMI Through is enabled, the power
consumption slightly increases.
Note
This setting is fixed to “Off” when “Auto Standby” is set to
Off”.
76


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR828 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR828 in the language / languages: English as an attachment in your email.

The manual is 4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR828

Onkyo TX-NR828 Quick start guide - English - 4 pages

Onkyo TX-NR828 Quick start guide - German - 4 pages

Onkyo TX-NR828 User Manual - German - 152 pages

Onkyo TX-NR828 Quick start guide - Dutch - 4 pages

Onkyo TX-NR828 User Manual - Dutch - 152 pages

Onkyo TX-NR828 Quick start guide - French - 4 pages

Onkyo TX-NR828 User Manual - French - 152 pages

Onkyo TX-NR828 Quick start guide - Italian - 4 pages

Onkyo TX-NR828 User Manual - Italian - 152 pages

Onkyo TX-NR828 Quick start guide - Swedish - 4 pages

Onkyo TX-NR828 User Manual - Swedish - 152 pages

Onkyo TX-NR828 Quick start guide - Spanish - 4 pages

Onkyo TX-NR828 User Manual - Spanish - 152 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info