553769
82
Zoom out
Zoom in
Previous page
1/97
Next page
82
Operating Other Manufacturers Devices Using
the Remote Controller
The remote controller has three learning functions. One
is entering the pre-programmed code for a remote con-
troller of another manufacturer. Another is the normal
learning function that enables the remote controller to
learn the codes directly from other remote controllers
(See page 86). And the last is a macro learning function
that enables you to program a series of operations into
the remote controller so that the operations can all be
performed at once by pressing one button (See page 88).
By entering a pre-programming code, you can have the
RC-511M remote controller operate a component made
by another manufacturer. The buttons that are used for
operation are given on pages 84-85.
Caution
With some brand’s components, some buttons may not
work correctly. In this case, program the command
directly from the other remote controller normally (See
page 86).
When entering the code of Onkyo DVD players:
There are three SETTING numbers. Choose the SET-
TING number according to how you will be using the
DVD player.
No. 601/613: These codes are for operating the Onkyo
DVD player by pointing the remote controller directly
at it, either because it does not have an terminal, or
it does but you are not connecting it with an cable.
First enter 601 and if it does not operate properly, enter
613.
No. 600: This code is for Onkyo DVD players that have
an terminal that you are connecting to the
TX-NR801/TX-NR801E with an cable. You will
then operate the DVD player by pointing the remote
controller at the remote control sensor on the
TX-NR801/TX-NR801E. You do not need to enter this
code because it is factory preset. However, if the code
has been changed to 601 or 613, then you will need to
change it back to 600.
Learning a Pre-programming Code
VOL
DISPLAY
Buttons that can
be pre-programmed
Numeric keys
SEND/LEARN
indicator
1
In the table on the next page nd the 3-
digit number for the manufacturer of the
component that you want to operate.
2
Turn on the component that you want to
operate (i.e., DVD, satellite tuner, or televi-
sion).
3
While holding down the MODE button on
the RC-511M that you want to program,
press the DISPLAY button, and then
release both buttons.
The SEND/LEARN indicator lights when the
MODE button is pressed and turns off when the
DISPLAY button is pressed. When the indicator
turns off, release both buttons. The SEND/
LEARN indicator lights again.
4
Within 30 seconds, enter the 3-digit code.
The SEND/LEARN indicator slowly flashes
twice. If the SEND/LEARN indicator quickly
flashes three times, then either a mistaken 3-digit
code was entered or an incorrect operation was
performed. If this occurs, return to step 3.
5
Press the button that you programmed
and check if the system operates cor-
rectly.
If the component does not operate properly,
return to step 3 and repeat the steps above.
If it still does not operate properly, program the
command directly from the other remote con-
troller normally (See page 86).
82


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR801 in the language / languages: English as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info