553769
35
Zoom out
Zoom in
Previous page
1/97
Next page
35
Selecting the Appropriate Setting
for Your Connections—Continued
To accurately set the output levels, it is recommended
to use a handheld sound pressure level (SPL) meter.
Set the meter to C-weighting and slow averaging. A
Radio Shack
®
SPL meter or equivalent is
recommended. Using the internal channel noise
generators, set each channel so that you read a 75
decibel sound pressure level.
Using the remote controller
Conguring Input
Settings Suitable for
Your Connections
These input settings should be made so that the
TX-NR801/TX-NR801E is optimized for your connec-
tions. If the default settings suit your connections, you
do not need to change any settings.
If you connected an MD recorder to the TAPE jack on
the TX-NR801/TX-NR801E, you can have “MD”
appear when the TAPE source button is pressed.
1
Press the TEST button.
A pink noise will be emitted from the
front left speaker.
At this time, the volume of the pink noise
will automatically increase to a
predetermined reference level (0 dB).
2
Remember the volume level of this
noise and then press the CH SEL
button.
The TX-NR801/TX-NR801E will now
emit the pink noise from the center
speaker.
3
Using the LEVEL / buttons,
adjust the volume level of the
noise from the center speaker so
that it is at the same level as that
emitted from the front left speaker.
4
Use the CH SEL and LEVEL /
buttons to select other speakers
and adjust the volumes until all
speakers are adjusted to the same
level.
5
Press the TEST button to complete
the procedure.
To Change the Display of the Input
Source from TAPE to MD
Press and hold down the TAPE
source button on the TX-NR801/
TX-NR801E until the display
changes from TAPE to MD (approx.
3 seconds).
When you use the remote controller to
perform the procedure, on the remote
controller, press the RCVR button and
hold down the TAP button for three sec-
onds.
To return the display to its original
setting, perform the same procedure.
DSP
A
-
FO
RM LISTENING MODE MEMORY
THX
SURROUNDDIRECT
/
PURE AUDIO STEREO
FM
MODE
MEMORY
ENTER
RE
TURN
SETUP
TUNING
PRESET
TAPETAPE
TAPE
TX-NR801/
TX-NR801E
Remote
controller
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR801 in the language / languages: English as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info