553769
27
Zoom out
Zoom in
Previous page
1/97
Next page
27
Connecting the Power
Before you plug in the TX-NR801/TX-NR801E, con-
firm that all connections have been made properly.
Turning on the power may cause a momentary power
surge, which might interfere with other electrical
equipment on the same circuit, such as computers. If
this happens, use a wall outlet on a different circuit.
(All models other than USA, Canadian and Austra-
lian models)
The TX-NR801/TX-NR801E is shipped with the
main power (POWER) switch in the on position
( ). When the power cord is plugged in for the
first time, the TX-NR801/TX-NR801E will automati-
cally enter the standby state and the STANDBY indi-
cator will light (same condition after step 2 below).
Before you can use the remote controller, you must
perform steps 1 and 2 above and place the TX-NR801/
TX
-
NR801E in the standby state.
Memory backup
The TX-NR801/TX-NR801E uses a battery-less mem-
ory backup system in order to retain radio presets and
other settings when it is unplugged or in the case of a
power failure. Although no batteries are required, the
TX-NR801/TX-NR801E must be plugged into an AC
outlet in order to charge the backup system.
(On other than USA, Canadian and Australian models,
the TX-NR801/TX-NR801E’s POWER switch must be
set to ON in order to charge the backup system.) Once it
has been charged, the TX-NR801/TX-NR801E will
retain the settings for several weeks, although this
depends on the environment and time will be shorter in
humid climates.
DSP
A
-
FO
RM LISTENING MODE MEMORY
THX
SURROUNDDIRECT
/
PURE AUDIO STEREO
FM
MODE
MEMORY
ENTER
RE
TURN
SETUP
TUNING
PRESET
DSP
A
-
FO
RM LISTENING MODE MEMORY
THX
SURROUNDDIRECT
/
PURE AUDIO STEREO
FM
MODE
MEMORY
ENTER
RE
TURN
SETUP
TUNING
PRESET
ON
RCVR
STANDBY
STANDBY/ON STANDBY/ON
POWER
(USA, Canadian and Australian models)
(Other models)
STANDBY indicator STANDBY indicator
To wall outlet
To wall outlet
Turning on the Power
1
Plug the power cord into an AC
wall outlet.
(USA, Canadian and Australian
models)
The STANDBY indicator will light up.
(Other models)
Press the POWER switch to set the
TX-NR801/TX-NR801E to standby
state.
The STANDBY indicator will light up.
2
Press the STANDBY/ON button to
turn on the TX-NR801/TX-NR801E.
The display will light up and the
STANDBY indicator will turn off.
If you press the STANDBY/ON button
again, the TX-NR801/TX-NR801E
returns to the standby state.
ON
STANDBY
OFF
ON
POWER
STANDBY
STANDBY/ON
STANDBY
Turn off
Turning on the Power from the
Remote Controller
1
Press the RCVR MODE button.
The RCVR MODE button lights.
2
Press the ON button to turn on the
TX-NR801/TX-NR801E (take it out
of the standby state).
To return the TX-NR801/TX-NR801E
to the standby state, press the
STANDBY button.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR801 in the language / languages: English as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info