553769
7
Zoom out
Zoom in
Previous page
1/97
Next page
7
Before Using the TX-NR801/TX-NR801E
The worldwide model has a voltage selector for com-
patibility with power systems around the world. Before
you plug in this model, make sure that the voltage selec-
tor is set to the correct voltage for your area. If it isn’t,
use a small screwdriver to set it appropriately. For
example, if the voltage in your area is 120 volts (V), set
the selector to “120V.And if it’s between 220 and 230
volts (V), set it to “220-230V.
Notes:
The supplied batteries should last for about six
months, although this will vary with usage.
If the remote controller doesn’t work reliably, try
replacing both batteries.
Don’t mix new and old batteries, or different types of
batteries.
If you intend not to use the remote controller for a
long time, remove the batteries to prevent possible
leakage and corrosion.
Dead batteries should be removed as soon as possible
to prevent possible leakage and corrosion.
To use the remote controller, point it at the TX-NR801/
TX-NR801E’s remote control sensor, as shown below.
The TX-NR801/TX-NR801E’s STANDBY indicator
flashes while a signal is being received from the remote
controller.
Notes:
The remote controller may not work reliably if the
TX-NR801/TX-NR801E is subjected to bright light,
such as direct sunlight or inverter-type fluorescent
lights. Keep this in mind when installing the
TX-NR801/TX-NR801E.
If another remote controller of the same type is used
in the same room, or the TX-NR801/TX-NR801E is
installed close to equipment that uses infrared rays,
the remote controller may not work reliably.
Don’t put anything, such as a book, on the remote
controller, because the buttons may be pressed inad-
vertently, thereby draining the batteries.
The remote controller may not work reliably if the
TX-NR801/TX-NR801E is installed in a rack behind
colored glass doors. Keep this in mind when install-
ing the TX-NR801/TX-NR801E.
The remote controller will not work if there’s an
obstacle between it and the TX-NR801/
TX-NR801E’s remote control sensor.
Setting the Voltage Selector
(Worldwide model only)
Installing the Batteries
1
Remove the battery compartment cover
by pressing it and sliding it in the direc-
tion shown by the arrow below.
2
Insert the two supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
3
After the batteries are installed and
seated correctly, replace the compart-
ment cover .
SURR
BACK/
ZONE 2
SPEAKERS
AUDIO
VIDEO
S VIDEO
MONITOR
OUT
R
L
IN
IN
IN
IN
IN
ZONE 2
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
AUDIO
VIDEO
S VIDEO
COMPONENT
VIDEO
Y
P
B
PR
OUTPUT
INPUT 1
Y
P
B
PR
INPUT 2
Y
P
B
PR
FRONT SPEAKERS
L
RL
R
SURR SPEAKERS
CENTER
SPEAKER
R
L
R
L
OUT
OUT
OUT
I
R
IN
OUT
REMOTE
CONTROL
PHONO
DIGITAL
IN
PRE OUT
DIGITAL
OUT
OPT
OPT
2
1
2
1
2
3
FRONT
SUB
SURR
R
L
AUDIO
R
L
CD
TAPE
R
L
AUDIO
1
3
GND
SURR
BACK/
ZONE 2
IN
OUT
COAX
R
L
MULTI
CH
INPUT
FRONT
SUB
SURR
SURR
BACK
CENTER
R
L
R
L
AM
FM
75
CENTER
ANTENNA
IN
IN
(
Net
-
Tune
)
ETHERNET
4 OHMS MIN. OR
6 OHMS MIN.
/SPEAKER
CAUTION
:
SPEAKER
IMPEDANCE
SEE INSTRUCTION
MANUAL FOR
CORRECT SETTINGS.
AV RECEIVER
MODEL NO. TX
-
NR
801
VOLTAGE
SELECTOR
220
-
230V
120V
AC
OUTLETS
AC 230
-
240
V 50
Hz
SWITCHED
TOTAL 100
W MAX.
120V
VOLTAGE
SELECTOR
220-230V
Using the Remote Controller
30˚
30˚
Approx. 16 ft. (5 m)
Remote control sensor
Standby indicator
TX-NR801/TX-NR801E
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR801 in the language / languages: English as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info