548135
51
Zoom out
Zoom in
Previous page
1/89
Next page
Troubleshooting
51
Troubleshooting
Before starting the procedure
Problems may be solved by simply turning the power on/off
or disconnecting/connecting the power cord, which is easier
than working on the connection, setting and operating
procedure. Try the simple measures on both the unit and
the connected device. If the problem is that the video or
audio is not output or the HDMI linked operation does not
work, disconnecting/connecting the HDMI cable may solve
it. When reconnecting, be careful not to wind the HDMI
cable since if wound the HDMI cable may not fit well. After
reconnecting, turn off and on the unit and the connected
device.
Resetting the unit
Resetting the unit to the status at the time of shipment may
solve the problem. If the measures above do not solve the
problem, reset the unit with the following procedure. If you
reset the unit status, your preferences will be reset to the
defaults. Note them down before starting reset.
How to reset
1.
While holding down CBL/SAT on the main unit (note
that step 2 must be performed with this button pressed
down)
2.
Press ON/STANDBY on the unit.
"Clear" is appeared
on the display and the unit will enter standby mode.
Clear
2
1
How to reset the remote controller
1.
While holding down
1
RCV on the remote controller
(note that step 2 must be performed with this button
pressed down)
2.
Press and hold down
2
HOME until the
3
remote
indicator lights (about 3 seconds). Within 30 seconds,
press
1
RCV again.
1
2
3
Power
Can not turn on the unit
• Make sure that the power cord is properly plugged into
the wall outlet.
• Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
The unit turns off unexpectedly
• The unit will automatically enter standby mode when
Auto Standby has been set and launches.
The unit turns off and after restoring the power, it
turns off again
• The protection circuit has been activated. Remove
the power cord from the wall outlet immediately. Make
sure that all speaker cables and input sources are
properly connected, and leave the unit with its power
cord disconnected for 1 hour. After that, reconnect the
power cord and turn the power on. If the unit turns off
again, avoid resetting it and unplug the power cord. Then
contact your Onkyo dealer.
Caution: If "CHECK SP WIRE" is appeared on the display,
the speaker cables may be shorting.
WARNING: If smoke, smell or abnormal noise is produced
by the unit, unplug the power cord from the wall outlet
immediately and contact the dealer or Onkyo Support.
Audio
There is no sound, or it is very quiet
• Make sure that the proper input source is selected.
• Make sure that connecting plugs are pushed in all the
way.
• Make sure that the inputs and outputs of all components
are connected properly.
• Make sure that the polarity of the speaker cables is
correct, and that no bare wires are in contact with the
metal part of speaker terminals.
• Make sure that the input source is properly selected.
• Make sure that the speaker cables are not shorting.
• Check the volume. The volume level is adjustable
between Min, 1 to 79, Max (80) It is normal that the unit
volume level is set up to 40 or around.
• If the MUTING indicator on the display flashes, press
MUTING on the remote controller to unmute the unit.
• While headphones are connected to the PHONES jack,
no sound is output from the speakers.
• If there is no sound from a BD/DVD player connected to
an HDMI IN, check the BD/DVD player’s output settings,
and be sure to select a supported audio format.
• Check the digital audio output setting on the connected
component. On some game consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• If your turntable uses an MC cartridge, you must
connect an MC head amp, or an MC transformer.
• Make sure that none of the connecting cables are bent,
twisted, or damaged.
• Not all listening modes use all speakers.
• Specify the speaker distances and adjust the individual
speaker levels.
• Make sure that the speaker setup microphone is not still
connected.
• If the input signal format is set to "PCM" or "DTS", set it
to "Off".
Only the front speakers produce sound
• When the Stereo or Mono listening mode is selected,
only the front speakers and subwoofer produce sound.
• Make sure the speakers are configured correctly.
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR636 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR636 in the language / languages: English as an attachment in your email.

The manual is 16,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR636

Onkyo TX-NR636 User Manual - English - 20 pages

Onkyo TX-NR636 User Manual - German, Dutch - 100 pages

Onkyo TX-NR636 User Manual - French - 40 pages

Onkyo TX-NR636 User Manual - Italian, Swedish - 100 pages

Onkyo TX-NR636 User Manual - Spanish - 40 pages

Onkyo TX-NR636 User Manual - Finnish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info