462088
69
Zoom out
Zoom in
Previous page
1/84
Next page
69
En
Can’t access the music files on a USB device
Standby power consumption
The sound changes when I connect my
headphones
The speaker distance cannot be set as required
The display doesn’t work
How do I change the language of a multiplex
source
The u functions don’t work
The functions System On/Auto Power On and
Direct Change don’t work for components
connected via u
When performing “Automatic Speaker Setup”,
the measurement fails showing the message
“Ambient noise is too high.”
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these
settings.
On the AV receiver, press the input selector for the
input source that you want to set and the
SETUP button
simultaneously. While holding down the input selector
button, press
SETUP until “Video ATT:ON” appears
on the display. Then, release both buttons. To reactivate
the setting, repeat the above process so that “Video
ATT:OFF” appears on the display, and release the
buttons.
•Video Attenuation
This setting can be made for the BD/DVD, VCR/DVR,
CBL/SAT, GAME or AUX input.
If you have a game console connected to the composite
video input, and the picture isn’t very clear, you can
attenuate the gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain is reduced by 2 dB.
If the picture on your TV/monitor connected to
HDMI OUT is unstable, try switching the
DeepColor function off
To turn off the DeepColor function, simultaneously
press the CBL/SAT and 8ON/STANDBY buttons on
the AV receiver. While holding down CBL/SAT, press
8ON/STANDBY until “Off” appears on the display.
Then, release both buttons. To reactivate the DeepColor
function, repeat the above process until “On” appears
on the display and release the buttons.
USB Device Playback
Make sure the USB device is plugged in properly.
The AV receiver supports USB devices that support
the USB mass storage device class. However,
playback may not be possible with some USB
devices even if they conform to the USB mass
storage device class.
USB memory devices with security functions cannot
be played.
Others
In the following cases, the power consumption in
standby mode may reach up to a maximum of 37 W:
You are using the Universal Port jack.
–“Network Control” is set to “Enable” in the
Network” setting.
–“HDMI Control (RIHD)” setting is set to “On”.
(Depending on the TV status, the AV receiver
will enter standby mode as usual.)
–TheHDMI Through” setting is set to other than
Off”.
16, 52,
53, 54
When a pair of headphones is connected, the
listening mode is set to Stereo, unless it’s already set
to Stereo, Mono, Direct or Pure Audio.
In some cases, corrected values suitable for home
theater use may be set automatically.
The display is turned off when the Pure Audio
listening mode is selected.
Use the “Multiplex” setting on the “Audio Adjust
menu to select “Main” or “Sub”.
45
To use u, you must make an u connection and
an analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally.
18
These functions don’t work when Zone 2 is turned
on.
18
This can be caused by a malfunction in your speaker
unit. Check if the unit produces normal sounds.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to standby.
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR579 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR579 in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR579

Onkyo TX-NR579 User Manual - German - 168 pages

Onkyo TX-NR579 User Manual - Dutch - 168 pages

Onkyo TX-NR579 User Manual - French - 168 pages

Onkyo TX-NR579 User Manual - Italian - 168 pages

Onkyo TX-NR579 User Manual - Spanish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info