492660
106
Zoom out
Zoom in
Previous page
1/168
Next page
Appendix
En-106
When performing Automatic Speaker Setup, the
measurement fails and the message “Ambient
noise is too high.” is displayed.
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these
settings.
On the AV receiver, press the input selector for the input
source that you want to set and the SETUP button
simultaneously. While holding down the input selector
button, press SETUP until “Video ATT :On” appears
on the AV receiver’s display. Then, release both buttons.
To turn the setting off, repeat the above process so that
Video ATT :Off” appears on the AV receiver’s
display, and release the buttons.
Video Attenuation
This setting can be made for the BD/DVD, CBL/SAT,
STB/DVR, GAME 1, AUX, or USB input.
If you have a game console connected to the composite
video input, and the picture isn’t very clear, you can
attenuate the gain.
Video ATT :Off: The gain is not changed (default).
Video ATT :On: The gain is reduced by the values
specified below.
2 dB for the ZONE 2 OUT V and HDMI output.
6 dB for the MONITOR OUT V output.
Note
With the USB input selector, this setting is only available when
an iPod/iPhone is connected and set to Extended Mode (Video)
or Standard Mode.
If the picture on your TV/monitor connected to
the HDMI output is unstable, try switching the
DeepColor function off
To turn off the DeepColor function, simultaneously
press the STB/DVR and 8ON/STANDBY buttons on
the AV receiver. While holding down STB/DVR, press
8ON/STANDBY until “Deep Color:Off” appears on
the AV receiver’s display. Then, release both buttons.
To reactivate the DeepColor function, repeat the above
process until “Deep Color:On” appears on the AV
receiver’s display and release the buttons.
The AV receiver can upconvert component video and
composite video sources for display on a TV connected to
the HDMI output. However, if the picture quality of the
source is poor, upconversion may make the picture worse
or disappear altogether.
In this case, try the following:
Tip
To by-pass the upconversion, set the “Picture Mode” setting to
Direct” ( page 78).
This can be caused by a malfunction in your speaker
unit. Check if the unit produces normal sounds.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in.
Onkyo is not responsible for damages (such as CD rental
fees) due to unsuccessful recordings caused by the unit’s
malfunction. Before you record important data, make
sure that the material will be recorded correctly.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to standby.
Important Note Regarding Video Playback
1
If the video source is connected to a component
video input, connect your TV to COMPONENT
VIDEO MONITOR OUT.
If the video source is connected to a composite video
input, connect your TV to MONITOR OUT V.
2
On the main menu, select “Input/Output Assign”,
and then “Component Video Input” ( page 65).
If the video source is connected to COMPONENT
VIDEO IN 1, select the relevant input selector, and
assign it to “IN1”.
If the video source is connected to COMPONENT
VIDEO IN 2, select the relevant input selector, and
assign it to “IN2”.
If the video source is connected to a composite video
input, select the relevant input selector, and assign it to
-----”.
106


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR5010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR5010 in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR5010

Onkyo TX-NR5010 User Manual - German - 168 pages

Onkyo TX-NR5010 User Manual - Dutch - 168 pages

Onkyo TX-NR5010 User Manual - French - 168 pages

Onkyo TX-NR5010 User Manual - Italian - 168 pages

Onkyo TX-NR5010 User Manual - Swedish - 168 pages

Onkyo TX-NR5010 User Manual - Spanish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info