553766
23
Zoom out
Zoom in
Previous page
1/116
Next page
23
En
Note
*1
TX-NR5008
*2
Connect a turntable (MM) that has built-in a phono preamp to TV/CD IN or connect it to PHONO IN with the phono preamp turned
off. If your turntable (MM) doesn’t have a phono preamp, connect to PHONO IN. If your turntable has a moving coil (MC) type car-
tridge, you’ll need a commercially available MC head amp or MC transformer to connect to PHONO IN. See your turntable’s man-
ual for details.
If your turntable has a ground wire, connect it to the AV receiver’s GND screw. With some turntables, connecting the ground wire
may produce an audible hum. If this happens, disconnect it.
*3
When you connect your personal computer to PC IN and select PC input selector, video of the personal computer is output from
HDMI output. However, because the AV receiver selects the video input in the order of HDMI > component > analog RGB, if you
have assigned HDMI IN to the PC input selector, the AV receiver will output signals from HDMI IN in priority to PC IN.
*4
Before using the multichannel input, you must assign it to an input selector. See “Analog Audio Input” ( 50). To select the multi-
channel input, see “Audio Selector” ( 68). To adjust the subwoofer sensitivity for the multichannel input, see “Subwoofer Input
Sensitivity” ( 50).
The AV receiver can output audio and video signals from the AUX INPUT jacks to the VCR/DVR OUT jacks.
With connection D, you can listen and record audio from the external components while you are in Zone 2/3. You can listen and record
audio from the external components in the main room; you can listen to the audio in Zone 2/3 as well.
With connection C, you can enjoy Dolby Digital and DTS. (To record or listen in Zone 2/3 as well, use C and D.)
How to record the video
With the connections described above, you cannot record the video through the AV receiver. To make a connection for
video recording ( 38).
With u (Remote Interactive), you can use the following
special functions:
Auto Power On
When you start playback on a component connected via
u while the AV receiver is on Standby, the AV
receiver will automatically turn on and select that com-
ponent as the input source.
Direct Change
When playback is started on a component connected via
u, the AV receiver automatically selects that compo-
nent as the input source.
Remote Control
You can use the AV receiver’s remote controller to con-
trol your other u-capable Onkyo components, point-
ing the remote controller at the AV receiver’s remote
control sensor instead of the component. You must enter
the appropriate remote control code first ( 93).
Note
•Use only u cables for u connections. u cables are supplied
with Onkyo players (DVD, CD, etc.).
Some components have two u jacks. You can connect either
one to the AV receiver. The other jack is for connecting addi-
tional u-capable components.
Connect only Onkyo components to u jacks. Connecting other
manufacturer’s components may cause a malfunction.
Some components may not support all u functions. Refer to
the manuals supplied with your other Onkyo components.
While Zone 2 or Zone 3 is on, the Auto Power On and Direct
Change u functions do not work.
Do not use u connections if you use HDMI Control (RIHD)
( 65).
Connecting Onkyo u Components
Step 1:
Make sure that each Onkyo component is connected
with an analog audio cable (connection D in the hookup
examples) ( 22).
Step 2:
Make the u connection (see illustration below).
Step 3:
If you’re using an RI Dock, or cassette tape deck,
change the Input Display ( 31).
IN
TV/CD
L
R
LR
IN
BD/DVD
L
R
REMOTE
CONTROL
ANALOG
AUDIO OUT
LR
ANALOG
AUDIO OUT
e.g., CD player
e.g., DVD player
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR5008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR5008 in the language / languages: English as an attachment in your email.

The manual is 5,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR5008

Onkyo TX-NR5008 User Manual - German - 228 pages

Onkyo TX-NR5008 User Manual - Dutch - 228 pages

Onkyo TX-NR5008 User Manual - French - 232 pages

Onkyo TX-NR5008 User Manual - Italian - 228 pages

Onkyo TX-NR5008 User Manual - Swedish - 228 pages

Onkyo TX-NR5008 User Manual - Spanish - 232 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info