553765
156
Zoom out
Zoom in
Previous page
1/164
Next page
156
Troubleshooting—Continued
With some CD and LD players, you won’t be able to
playback DTS material properly even though your
player is connected to a digital input on the AV
receiver. This is usually because the DTS bitstream
has been processed (e.g., output level, sampling rate,
or frequency response changed) and the AV receiver
doesn’t recognize it as a genuine DTS signal. In such
cases, you may hear noise.
When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a mal-
function.
The beginning of audio received by an HDMI IN
can’t be heard
Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio sig-
nals, audio output may not start immediately.
There’s no picture
Make sure that all video connecting plugs are pushed
in all the way (page 29).
Make sure that each video component is properly con-
nected (pages 31 to 46).
If your TV is connected to the HDMI output, set the
“Monitor Out” setting other than “Analog” (page 52),
and select “- - - - -” in the “HDMI Input Setup” on
page 54 to watch composite video, S-Video, and com-
ponent video sources.
If your TV is connected to the COMPONENT VIDEO
MONITOR OUT, S MONITOR OUT, or V MONI-
TOR OUT, set the “Monitor Out” setting to “Analog”
(page 52), and select “- - - - -” in the “Component
Video Input Setup” on page 55 to watch composite
video and S-Video sources.
If the video source is connected to a component video
input, you must assign that input to an input selector
(page 55), and your TV must be connected to either
the HDMI OUT or COMPONENT VIDEO MONI-
TOR OUT (pages 31 and 35).
If the video source is connected to an HDMI input,
you must assign that input to an input selector
(page 54), and your TV must be connected to the
HDMI outputs (page 31).
While the Pure Audio listening mode is selected, the
video circuitry is turned off and only video signals
input through HDMI IN can be output.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
If you selected “Both (Main)” or “Both (Sub)” in the
“Monitor Out” setting, no picture may appear on your
TV that is connected to a secondary HDMI output (not
a priority HDMI output). In this case, change the set-
ting to “Both” (page 52).
There’s no picture from a source connected to
an HDMI IN
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not guaranteed (page 31).
When the “Monitor Out” setting is set to “Analog”,
and the “Resolution” setting is set to anything other
than “Through” (page 53), no video is output by the
HDMI outputs.
When the “Resolution” (page 53) is set to any resolu-
tion not supported by the TV, no video is output by the
HDMI outputs.
If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that your TV does not
support the current video resolution and you need to
select another resolution on your DVD player.
The onscreen menus don’t appear
If your TV is connected to the analog outputs, set the
“Monitor Out” setting to “Analog” (page 52).
(European and Asian models) Specify the TV sys-
tem used in your area in the “TV Format Setup” on
page 59.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
The picture is distorted
(European and Asian models) Specify the TV sys-
tem used in your area in the “TV Format Setup” on
page 59.
The immediate display does not appear
If you select other than “Analog” in the “Monitor Out”
setting (page 52), the immediate display will not
appear when the input signal from the COMPONENT
VIDEO IN is output to a device connected to the
COMPONENT VIDEO MONITOR OUT.
Depending on the input signal, the immediate display
may not appear when the input signal from the HDMI
input is output to a device connected to the HDMI out-
put.
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t
appear
Relocate your antenna.
Move the AV receiver away from your TV or com-
puter.
Listen to the station in mono (page 73).
When listening to an AM station, operating the remote
controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
Video
Tuner
156


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR5007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR5007 in the language / languages: English as an attachment in your email.

The manual is 17,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR5007

Onkyo TX-NR5007 User Manual - German - 328 pages

Onkyo TX-NR5007 User Manual - Dutch - 328 pages

Onkyo TX-NR5007 User Manual - French - 328 pages

Onkyo TX-NR5007 User Manual - Italian - 328 pages

Onkyo TX-NR5007 User Manual - Swedish - 328 pages

Onkyo TX-NR5007 User Manual - Spanish - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info