492661
90
Zoom out
Zoom in
Previous page
1/168
Next page
Advanced Operations
En-90
Muting Zones
Operating on the remote controller
Tip
To unmute, press ZONE followed by MUTING again. Zones can
also be unmuted by adjusting the volume.
Note
ZONE 2 LINE OUT and FRONT WIDE/ZONE 2 L/R output
2ch PCM and analog input sources. To listen to the PCM source,
you need to make an HDMI connection ( page 21). If no
sound is heard when an input source is selected, check if the
source is connected to an analog input and HDMI input.
Only analog input sources are output by the ZONE 3 LINE OUT
and FRONT HIGH/ZONE 3 L/R terminals. Digital input
sources are not output. If no sound is heard when an input source
is selected, verify that the source is connected to an analog input.
(North American models) You can select different radio
stations for the main room and Zone 2 by connecting the supplied
antennas respectively ( page 24).
(North American models) When the main room and Zone 2
share the same input source, if the input selector of the main room
is TUNER, you cannot select different radio stations for the main
room and Zone 2 respectively.
(European models) You cannot select different AM or FM radio
stations for your main room and Zone 2/3. The same AM/FM
radio station will be heard in each room. Namely, if you have
selected an FM station for the main room, that station will also be
output in Zone 2/3.
You cannot select different radio stations for Zone 2 and Zone 3
respectively.
If Zone 2 and the main room share the same input source, only an
analog input signal is output.
If an HDMI component selected in Zone 2 outputs the sound
other than PCM, the sound is not output from FRONT
WIDE/ZONE 2 and ZONE 2 LINE OUT.
Both audio and video outputs from an HDMI component may
interrupt when the main room and Zone 2 are set to share the
same source or not.
When you have selected NET or USB as input selector, the last
selector selected will be set for Main room and Zone 2/3.
When Zone 2/3 is activated and its input selector is selected, the
power consumption of standby mode slightly increases.
While Zone 2/3 is on, u functions will not work.
The component connected to HDMI input other than HDMI IN
1/2/3/AUX INPUT is selected as an input source for Zone 2, the
linked operations of p may not work properly. In this
case, set the linked operations to Off on the source component.
When setting the AV receiver to standby mode while Zone 2/3 is
active, the Z2 or Z3 indicator is dimly lit.
Activating Zones in the main room when the listening mode is set
to Pure Audio will automatically switch it to Direct.
•“GAME2” cannot be selected as input sources for Zone 3.
When “GAME2” is the input source of Main room and Zone 3 is
set to share the same source, no sound will be output from Zone 3.
Even if you repeatedly press the remote controller’s ZONE to
select zones, the last zone selection will be retained once you
have switched to other components by pressing other REMOTE
MODE after pressing ZONE.
To control the AV receiver with the remote controller
while you’re in Zone, you’ll need a commercially available
multiroom remote control kit for each zone.
Multiroom kits are made by Niles and Xantech.
These kits can also be used when there isn’t a clear line of
sight to the AV receiver’s remote sensor, such as when it’s
installed inside a cabinet.
Using a Multiroom Kit with Zone
In this setup, the IR receiver in Zone picks up the infrared
signals from the remote controller and feeds them through
to the AV receiver in the main room via the connecting
block.
The miniplug cable from the connecting block should be
connected to the AV receiver’s IR IN jack, as shown
below.
1
Press ZONE repeatedly, and then press MUTING.
Using the Remote Controller in
Zone and Multiroom Control Kits
IR IN
Connecting
block
Remote controller
IR
receiver
Main room Zone
Signal flow
90


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR3010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR3010 in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR3010

Onkyo TX-NR3010 User Manual - German - 168 pages

Onkyo TX-NR3010 User Manual - Dutch - 168 pages

Onkyo TX-NR3010 User Manual - French - 168 pages

Onkyo TX-NR3010 User Manual - Italian - 168 pages

Onkyo TX-NR3010 User Manual - Swedish - 168 pages

Onkyo TX-NR3010 User Manual - Spanish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info