492661
43
Zoom out
Zoom in
Previous page
1/168
Next page
Turning On & Basic Operations
En-43
1
Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV receiver
is connected.
2
Set the speaker setup microphone at the Main
Listening Position a, and connect it to the SETUP
MIC jack.
The speaker setting menu appears.
Note
The on-screen menus appear only on a TV that is connected
to HDMI OUT MAIN. If your TV is connected to other
video outputs, use the AV receiver’s display when changing
settings.
3
When you’ve finished making the settings, press
ENTER.
Perform the “Speaker Setup” according to your
speaker configuration:
Speakers Type(Front A) ( page 66)
Speakers Type(Front B) ( page 66)
Powered Zone 2 ( page 66)
Powered Zone 3 ( page 66)
11ch Playback ( page 66)
Subwoofer ( page 67)
Speaker setup microphone
SETUP MIC jack
MultEQ XT32: Auto Setup
AUDYSSEY
Speakers Type(Front A)
Speakers Type(Front B)
Powered Zone 2
Powered Zone 3
11ch Playback
Subwoofer
Normal
No
No
No
No
2ch
If you use a powered subwoofer(s), go to step 4. If not,
go to step 5.
If “Speakers Type(Front A)” or “Speakers
Type(Front B)” is set to “Digital Crossover”, a
confirmation screen appears. Select “Next (2-7.
Digital Processing Crossover Network)” to display
the screen for Digital Processing Crossover Network
( page 71). Continue with the settings.
4
Adjust the subwoofer volume level to 75 dB, and
then press ENTER.
Test tones are played through the subwoofer. Use the
volume control on the subwoofer.
When the “Subwoofer” setting is set to “1ch” only,
the left-hand subwoofer (SW1) will be measured.
When the “Subwoofer” setting is set to “1ch” with
two subwoofers connected, the right-hand subwoofer
(SW2) will not be measured and no sound will be
output.
An error will occur if you set “Subwoofer” to2ch
without connecting any subwoofers, or with only one
subwoofer connected.
Note
If your subwoofer does not have a volume control, disregard
the displayed level and press ENTER to proceed to the next
step.
If you set the subwoofer’s volume control to its maximum
and the level displayed is lower than 75 dB, leave the
subwoofer’s volume control at its maximum and press
ENTER to proceed to the next step.
If you use two subwoofers, perform this step twice.
5
Use q/w to select “Audyssey Quick Start” or
“Audyssey MultEQ XT32 Full Calibration”, and
then press ENTER.
6
Press ENTER.
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ XT32 Room Correction and
Speaker Setup runs. This process takes a few minutes.
Please refrain from talking during measurements
and do not stand between speakers and the
microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ XT32 Room Correction and
Speaker Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to
step 9.
7
Place the speaker setup microphone at the next
position, and then press ENTER.
Audyssey MultEQ XT32 performs more
measurements. This takes a few minutes.
8
When prompted, repeat step 7.
To be continued
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR3010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR3010 in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR3010

Onkyo TX-NR3010 User Manual - German - 168 pages

Onkyo TX-NR3010 User Manual - Dutch - 168 pages

Onkyo TX-NR3010 User Manual - French - 168 pages

Onkyo TX-NR3010 User Manual - Italian - 168 pages

Onkyo TX-NR3010 User Manual - Swedish - 168 pages

Onkyo TX-NR3010 User Manual - Spanish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info