553767
84
Zoom out
Zoom in
Previous page
1/116
Next page
84
En
Controlling Zone 2/3 with the Remote
Controller
Note
To control Zone 2/3, you must press the remote controller’s
ZONE first.
ZONE turns red while Zone 2 is on, and green while Zone 3 is
on.
Note
Only analog input sources are output by the ZONE 2/3 PRE
OUT and FRONT WIDE/ZONE 2 L/R, SURR BACK/ZONE
3 L/R terminals. Digital input sources are not output. If no sound
is heard when an input source is selected, check if it’s connected
to an analog input.
You cannot select different AM or FM radio stations for your
main room and Zone 2/3. The same AM/FM radio station will be
heard in each room. For example, if you have an FM station for
the main room, that station will also be used in Zone 2.
When you connect Zone 3 speakers directly to the AV receiver,
listening modes that require surround back speakers such as
Dolby EX, DTS-ES or THX Surround EX are unavailable.
When the input selector of Zone 2/3 is selected, power consump-
tion on standby mode slightly increases.
While Zone 2/3 is on, u functions will not work.
Adjusting the Volume for Zones
Muting Zones
Adjusting the Tone and Balance of Zones
Note
Zones can also be unmuted by adjusting the volume.
The Zone 2 volume, tone, and balance function have no effect on
ZONE 2 PRE OUT when the “Zone 2 Out” setting is set to
Fixed” ( 83) and “Powered Zone 2” setting is set to “Not
Act” ( 82).
The Zone 3 volume, tone, and balance function have no effect on
ZONE 3 PRE OUT when the “Zone 3 Out” setting is set to
Fixed” ( 83) and “Powered Zone 3” setting is set to “Not
Act” ( 82).
Even if you repeatedly press the remote controller’s ZONE to
select zones, the last zone selection will be retained once you
have switched to other components by pressing other REMOTE
MODE after pressing ZONE.
1
Press ZONE repeatedly, then point the remote
controller at the AV receiver and press ON.
Tip
•The ZONE 2/3 12V TRIGGER OUT goes high (+12 V).
2
To select an input source for Zone 2/3, press
ZONE repeatedly, followed by INPUT SELEC-
TOR.
To select AM or FM, press TUNER input selector
and ZONE repeatedly.
(North American models) You can also select SIR-
IUS.
3
To turn off Zone 2/3, press ZONE repeatedly, fol-
lowed by STANDBY.
INPUT
SELECTOR
ON
ZONE
STANDBY
On the remote controller, press ZONE repeatedly,
and then use VOL q/w.
On the AV receiver, press ZONE 2 or ZONE 3
(the ZONE 2/3 indicator and Zone 2/3 selector on
the display flashes) and press LEVEL followed by
Up r/Down e within 8 seconds.
On the remote controller, press ZONE repeatedly,
and then press MUTING.
To unmute a zone, on the remote controller, press
ZONE, and then press MUTING again.
1
On the AV receiver, press ZONE 2 or ZONE 3.
2
Press the AV receiver’s TONE repeatedly to select
“Bass”, “Treble” or “Balance”.
3
Use e/r to adjust the bass, treble or balance.
You can boost or cut the bass or treble from –10 dB
to +10 dB in 2 dB steps.
You can adjust the balance from 0 in the center to
+10 dB to the right or +10 dB to the left in 2 dB
steps.
84


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR3008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR3008 in the language / languages: English as an attachment in your email.

The manual is 5,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR3008

Onkyo TX-NR3008 User Manual - German - 228 pages

Onkyo TX-NR3008 User Manual - Dutch - 228 pages

Onkyo TX-NR3008 User Manual - French - 232 pages

Onkyo TX-NR3008 User Manual - Italian - 228 pages

Onkyo TX-NR3008 User Manual - Swedish - 228 pages

Onkyo TX-NR3008 User Manual - Spanish - 232 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info