553767

Onkyo TX-NR3008 Manual

51
Zoom out
Zoom in
Previous page
1/116
Next page
51
En
■ Speaker Impedance
` 4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
` 6ohms
:
Select if the impedances of all speakers are between
6 and 16 ohms.
Note
• When bridging is used, “Speaker Impedance” setting is fixed at
“8ohms”.
■ Speakers Type(Front A)
` Normal
:
Select this if you’ve connected your front speakers A
normally.
` Bi-Amp:
Select this if you’ve connected your front speakers A
for bi-amped operation. The Bi AMP indicator will
light (➔ 9).
` BTL:
Select this if you’ve connected your front speakers A
for bridged operation. The BTL indicator will light
(➔ 9).
Note
•“Bi-Amp” and “BTL” cannot be selected if “Speakers
Type(Front B)” is set to “Bi-Amp” or “BTL”.
• Surround back speakers and Powered Zone 3 cannot be used if
you select “Bi-Amp” or “BTL”.
•“Speakers Type(Front A)” is set to “Normal” if the “Front
High + Front Wide” setting is set to “Ye s ”.
■ Speakers Type(Front B)
` Not Use
:
Select this if you’re not using speakers B.
` Normal:
Select this if you’ve connected your front speakers B
normally.
` Bi-Amp:
Select this if you’ve connected your front speakers B
for bi-amped operation. The Bi AMP indicator will
light (➔ 9).
` BTL:
Select this if you’ve connected your front speakers B
for bridged operation. The BTL indicator will light
(➔ 9).
Note
•“Bi-Amp” and “BTL” cannot be selected if “Speakers
Type(Front A)” is set to “Bi-Amp” or “BTL”.
• Front high speakers, front wide speakers and Powered Zone 2
cannot be used if you select other than “Not Use”.
• Surround back speakers and Powered Zone 3 cannot be used if
you select “Bi-Amp” or “BTL”.
• This setting cannot be used if “Front High + Front Wide” set-
ting is set to “Ye s”.
■ Powered Zone 2, Powered Zone 3
See “Setting the Powered Zone 2/3” (➔ 82).
■ Front High + Front Wide
` Ye s:
Front High + Front Wide on.
` No
:
Front High + Front Wide off.
Listening mode that make use of “Front High + Front
Wide” setting is as follows;
Audyssey DSX (PLII/Neo:6 + Audyssey DSX included),
Orchestra, Unplugged, Studio-Mix, TV Logic, Game-
RPG, Game-Action, Game-Rock, Game-Sports, All Ch
Stereo, Full Mono.
Note
• When you have selected “Yes”,
–the “Surround Back” setting is set to “None”.
–the “Front High” or “Front Wide” setting is set to
“80Hz(THX)” if set to “None”.
•The “Front High + Front Wide” setting cannot be used in either
of the following cases;
–“Bi-Amp” or “BTL” is being used.
– Powered Zone 2/3 are being used.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
You can set the crossover frequencies, distances, and lev-
els of the front speakers A and front speakers B indepen-
dently. The other speakers (i.e., subwoofer, center,
surround, and surround back) use the same crossover fre-
quencies, distances, and levels for Speakers A and Speak-
ers B. Specify “Full Band” for speakers that can output
low frequency bass sounds adequately, for example,
speakers with a good sized woofer. For smaller speakers,
specify a crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies.
If you set up your speakers using Audyssey MultEQ XT32
Room Correction and Speaker Setup, please make sure
manually that any THX speakers are set to “80Hz(THX)”
crossover.
■ Subwoofer
` 1ch:
Audio signal is outputted from SW1 jack only.
` 2ch
:
Audio signal is outputted from SW1 and SW2
jacks.
` No:
Select if no subwoofer is connected.
This setting is set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function (➔ 32). For Speakers B, you
need to change the settings manually.
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR3008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR3008 in the language / languages: English as an attachment in your email.

The manual is 5,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR3008

Onkyo TX-NR3008 User Manual - German - 228 pages

Onkyo TX-NR3008 User Manual - Dutch - 228 pages

Onkyo TX-NR3008 User Manual - French - 232 pages

Onkyo TX-NR3008 User Manual - Italian - 228 pages

Onkyo TX-NR3008 User Manual - Swedish - 228 pages

Onkyo TX-NR3008 User Manual - Spanish - 232 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info