462084
81
Zoom out
Zoom in
Previous page
1/100
Next page
81
En
The beginning of audio received by an HDMI IN
can’t be heard
There’s no sound during Whole House Mode
There’s no picture
There’s no picture from a source connected to
an HDMI IN
The on-screen menus don’t appear
The on screen display does not appear
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t light
The remote controller doesn’t work
With some CD and LD players, you won’t be able to
playback DTS material properly even though your
player is connected to a digital input on the AV
receiver. This is usually because the DTS bitstream
has been processed (e.g., output level, sampling rate,
or frequency response changed) and the AV receiver
doesn’t recognize it as a genuine DTS signal. In such
cases, you may hear noise.
Playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may
produce a short audible noise. This is not a
malfunction.
Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio
signals, audio output may not start immediately.
Make sure you’ve selected an analog audio input. 47
Video
Make sure that all video connecting plugs are pushed
in all the way.
16
Make sure that each video component is properly
connected.
17, 18
If your TV is connected to the HDMI output(s),
select “-----” in the “HDMI Input” setup to watch
composite video, S-Video and component video
sources.
46
If the video source is connected to a component
video input, you must assign that input to an input
selector, and your TV must be connected to either
the HDMI output(s) or COMPONENT VIDEO
MONITOR OUT.
18, 46
If the video source is connected to a composite video
input, your TV must be connected to the HDMI
output(s) or the corresponding composite video
output.
18
If the video source is connected to an HDMI input,
you must assign that input to an input selector, and
your TV must be connected to the HDMI output(s).
17, 46
While the Pure Audio listening mode is selected, the
video circuitry is turned off and only video signals
input through HDMI IN can be output.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
If the “Monitor Out” setting is set to “Both(Main)
or “Both(Sub)” while your TV is connected to a
secondary HDMI output (not a primary HDMI
output), the picture may not appear. In this case,
change the setting to “Both”.
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not guaranteed.
93
When the resolution is set to any resolution not
supported by the TV, no video is output from the
HDMI outputs.
46
If the message “Resolution Error” appears on the
AV receiver’s display, this indicates that your TV
does not support the current video resolution and
you need to select another resolution on your DVD
player.
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
When the AV receiver is not connected to a TV via
HDMI, onscreen menus are not displayed.
Depending on the input signal, the on screen display
may not appear when the input signal from the
HDMI IN is output to a device connected to the
HDMI OUT MAIN.
59
Tuner
Relocate your antenna.
Move the AV receiver away from your TV or
computer.
Listen to the station in mono. 28
When listening to an AM station, operating the
remote controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
Remote Controller
Before operating this unit, be sure to press
RECEIVER.
Make sure that the batteries are installed with the
correct polarity.
4
Install new batteries. Don’t mix different types of
batteries, or old and new batteries.
4
Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the
AV receiver’s remote control sensor.
4
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
If the AV receiver is installed in a rack or cabinet
with colored-glass doors, the remote controller may
not work reliably when the doors are closed.
Make sure you’ve selected the correct remote
controller mode.
11, 75
When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
Make sure you’ve entered the correct remote control
code.
74
Make sure to set the same ID on both the AV
receiver and remote controller.
59
81


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1009 in the language / languages: English as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1009

Onkyo TX-NR1009 Quick start guide - English - 2 pages

Onkyo TX-NR1009 User Manual - German - 196 pages

Onkyo TX-NR1009 User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info