462084
75
Zoom out
Zoom in
Previous page
1/100
Next page
75
En
Onkyo components that are connected via u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
Controlling Onkyo components without u
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via u, use the
following remote control codes:
` 30627:
Onkyo DVD player without u
` 71817:
Onkyo CD player without u
` 32900/33100/33500:
Onkyo Blu-ray Disc player
` 32901/33104/33504:
Onkyo HD DVD player
` 70868:
Onkyo MD recorder without u
` 71323:
Onkyo CD recorder without u
` 82990:
Onkyo Dock without u
You can reset a REMOTE MODE to its default remote
control code.
You can reset the remote controller to its default settings.
By pressing the REMOTE MODE that’s been
programmed with the remote control code for your
component, you can control your component as described
below.
For details on entering a remote control code for other
components, see “Entering Remote Control Codes”
( page 74).
Controlling a TV
TV is preprogrammed with the remote control code for
controlling a TV that supports the p
*1
(limited to
some models). The TV must be able to receive remote
control commands via p and be connected to the
AV receiver via HDMI. If controlling your TV via
p doesn’t work very well, program your TV’s
remote control code into TV and use the TV remote mode
to control your TV.
Use the following remote control codes:
` 11807/13100/13500:
TV with p
Controlling a Blu-ray Disc/DVD Player, HD
DVD Player or DVD Recorder
BD/DVD is preprogrammed with the remote control code
for controlling a component that supports the p
*1
(limited to some models). The component must be able to
receive remote control commands via p and be
connected to the AV receiver via HDMI.
Use the following remote control codes:
` 32910/33101/33501/31612:
Blu-ray Disc/DVD player with p
*1
The p supported by the AV receiver is the CEC
system control function of the HDMI standard.
Remote Control Codes for Onkyo
Components Connected via u
1
Make sure the Onkyo component is connected with
an u cable and an analog audio cable (RCA).
See “Connecting Onkyo u Components” for details
( page 20).
2
Enter the appropriate remote control code for
REMOTE MODE, referring to the previous
section.
` 42157:
Onkyo cassette tape deck with u
` 81993:
Onkyo Dock with u
3
Press REMOTE MODE, point the remote
controller at the AV receiver, and operate the
component.
Resetting REMOTE MODE Buttons
1
While holding down REMOTE MODE that you
want to reset, press and hold down HOME until
REMOTE MODE button lights (about 3 seconds).
2
Within 30 seconds, press REMOTE MODE again.
REMOTE MODE button flashes twice, indicating
that the button has been reset.
Each of REMOTE MODE is preprogrammed with a
remote control code. When a button is reset, its
preprogrammed code is restored.
Note
The learning command is also reset.
Resetting the Remote Controller
1
While holding down RECEIVER, press and hold
down HOME until RECEIVER lights (about 3
seconds).
2
Within 30 seconds, press RECEIVER again.
RECEIVER flashes twice, indicating that the remote
controller has been reset.
Controlling Other Components
75


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1009 in the language / languages: English as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1009

Onkyo TX-NR1009 Quick start guide - English - 2 pages

Onkyo TX-NR1009 User Manual - German - 196 pages

Onkyo TX-NR1009 User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info