462084
43
Zoom out
Zoom in
Previous page
1/100
Next page
43
En
By using ACTIVITIES in Easy macro mode, you can
sequentially operate Onkyo components via simple
commands from a single-button press. These commands
are user-definable. See “Using Normal Macros”
( page 78).
MY MOVIE
First, the TV, the Onkyo DVD player, and the AV receiver
are turned on. The input selector is set to “BD/DVD”.
Finally the player starts playback.
*1
*1
Depending on the start-up time of your Blu-ray Disc/DVD
player, the AV receiver may not activate this playback
command. In this case, press 1 on the remote controller.
MY TV
First, the TV, the cable set-top box, and the AV receiver
are turned on. Then the input selector is set to
CBL/SAT”.
MY MUSIC
The Onkyo CD player and the AV receiver are turned on.
The input selector is set to “TV/CD”. Finally, the player
starts playback.
Note
While the Easy Macro command is being processed, you cannot
use other ACTIVITIES. If you want to operate other
components, first press ALL OFF and use the desired
ACTIVITIES.
Turning Off the Components
This button turns off all components activated by the Easy
Macro mode.
First, the related components stop and turn off. Second,
the AV receiver turns off. Finally, the TV turns off (or
enters standby mode).
*1*2
*1
This step doesn’t apply to MY MUSIC, with the default
settings.
*2
With some televisions, the power may not be turned off (or
enter standby mode).
Changing the Source Components
You can change the source components activated by the
Easy Macro mode.
Examples:
If you wished to use MY MUSIC to start the Onkyo
cassette recorder, you would press and hold down
MY MUSIC (about 3 seconds) while holding down
TV/CD until it flashes twice.
Restoring Default
You can restore ACTIVITIES to the default settings.
This section explains how to record the selected input
source to a component with recording capability.
AV Recording
Audio sources can be recorded to a recorder (e.g., cassette
tape deck, CDR, MD recorder). Video sources can be
recorded to a video recorder (e.g., VCR, DVD recorder).
Using Easy Macros
1
Press ACTIVITIES (MY MOVIE, MY TV, or
MY MUSIC) to start the Easy macro command.
The default sequences of actions are described below.
To change the related source component, see
“Changing the Source Components” shown later in
this chapter.
1
Press ALL OFF.
1
While holding down REMOTE MODE for the
playback component you wish to assign, press and
hold down the ACTIVITIES to be changed
(MY MOVIE, MY TV, or MY MUSIC) (about 3
seconds).
ACTIVITIES flashes twice, indicating that the
change is complete.
1
While holding down HOME, press and hold down
ALL OFF until ALL OFF lights (about 3 seconds).
2
Release HOME and ALL OFF, and press ALL OFF
again.
ALL OFF flashes twice.
Recording
1
Use the input selector buttons to select the source
that you want to record.
You can watch the source while recording. The AV
receiver’s MASTER VOLUME control has no effect
on recording.
2
On your recorder, start recording.
3
On the source component, start playback.
If you select another input source during recording,
that input source will be recorded.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1009 in the language / languages: English as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1009

Onkyo TX-NR1009 Quick start guide - English - 2 pages

Onkyo TX-NR1009 User Manual - German - 196 pages

Onkyo TX-NR1009 User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info