462084

Onkyo TX-NR1009 Manual

32
Zoom out
Zoom in
Previous page
1/100
Next page
32
En
Note
• You can cancel Audyssey MultEQ XT Room Correction and
Speaker Setup at any point in this procedure simply by
disconnecting the setup microphone.
• Do not connect or disconnect any speakers during
Audyssey MultEQ XT Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ XT Room Correction and Speaker
Setup starts.
• Changes to the room after Audyssey MultEQ XT Room
Correction and Speaker Setup requires you run
Audyssey MultEQ XT Room Correction and Speaker Setup
again, as room EQ characteristics may have changed.
3
When you’ve finished making the settings, press
ENTER.
Perform the “Speaker Setup” according to your
speaker configuration:
– Speakers Type(Front) (➔ page 47)
– Powered Zone 2 (➔ page 47)
– Powered Zone 3 (➔ page 47)
– Subwoofer (➔ page 48)
If you use a powered subwoofer(s), go to step 4. If
not, go to step 5.
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
optional unit setting may appear on the speaker
setting menu.
4
Adjust the subwoofer volume level to 75 dB, and
then press ENTER.
Test tones are played through the subwoofer. Use the
volume control on the subwoofer.
Note
• If your subwoofer does not have a volume control,
disregard the displayed level and press ENTER to proceed
to the next step.
• If you set the subwoofer’s volume control to its maximum
and the level displayed is lower than 75 dB, leave the
subwoofer’s volume control at its maximum and press
ENTER to proceed to the next step.
5
Use q/w to select “Audyssey Quick Start” or
“Audyssey MultEQ XT Full Calibration”.
6
Press ENTER.
Audyssey MultEQ
®
XT Room Correction and
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ XT Room Correction and Speaker
Setup runs. This process takes a few minutes. Please
refrain from talking during measurements and do
not stand between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ XT Room Correction and
Speaker Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to
step 9.
7
Place the setup microphone at the next position,
and then press ENTER.
Audyssey MultEQ XT performs more measurements.
This takes a few minutes.
8
When prompted, repeat step 7.
MultEQ XT: Auto Setup
AUDYSSEY
Speakers Type(Front) Normal
Powered Zone 2 No
Powered Zone 3 No
Subwoofer Yes
9
Use q/w to select an option, and then press
ENTER.
The options are:
` Save:
Save the calculated settings and exit
Audyssey MultEQ XT
Room Correction and
Speaker Setup
.
` Cancel:
Cancel Audyssey MultEQ XT Room Correction
and Speaker Setup
.
Tip
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using e/r.
10
Use q/w to select a target, and use e/r to change
the setting.
After the results of Audyssey MultEQ XT have been
saved, the menu will display the “Audyssey”
(➔ page 53), “Dynamic EQ” (➔ page 53),
“Dynamic Volume” (➔ page 53) settings.
Note
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• These settings are applied to all input selectors.
11
Press ENTER.
12
Disconnect the speaker setup microphone.
Subwoofer : Yes
Front : 100Hz
Center : 40Hz
Surround : 100Hz
Front Wide : None
Front High : None
Surround Back : 120Hz
Surround Back Ch : 2ch
Save
Cancel
MultEQ XT: Auto Setup
AUDYSSEY
-- Review Speaker Configuration --
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1009 in the language / languages: English as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1009

Onkyo TX-NR1009 Quick start guide - English - 2 pages

Onkyo TX-NR1009 User Manual - German - 196 pages

Onkyo TX-NR1009 User Manual - Dutch - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info