492647
68
Zoom out
Zoom in
Previous page
1/148
Next page
Advanced Operations
En-68
Note
This setting is fixed to “----” when the “HDMI
Control(RIHD)” setting is set to “Off”.
This setting is set to “Auto” automatically when the “HDMI
Control(RIHD)” setting is set to “On” for the first time.
If you set “Audio Return Channel” to “Auto”, the “Audio
Selector” settings of the TV/CD input selector will be
automatically switched to “ARC” ( page 64).
LipSync
` Off
` On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
InstaPrevue
These settings apply to “InstaPrevue” of the Home menu
( page 45) and specify the preview display of HDMI
video streams.
Sub Window
` Multi
:
Displays preview thumbnails all at once.
` Single:
Displays preview thumbnails one-by-one.
With this setting, you can set the number of preview
thumbnails displayed.
Position
(with “Sub Window” set to “Multi”)
` Top, Bottom
, Left, Right
(with “Sub Window” set to “Single”)
` Upper Left, Upper Right, Lower Left, Lower Right
With this setting, you can set the position of preview
thumbnails on the TV screen.
Note
Depending on video signals, the picture may not be properly
rendered on the preview thumbnails of InstaPrevue.
Auto Standby
Auto Standby
` Off
` On
When “Auto Standby” is set to “On”, the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video signal
input.
Auto Standby” will appear on the AV receiver’s display
and OSD 30 seconds before the Auto Standby comes on.
Default setting: On (European, Australian and Asian
models), Off (North American and Taiwanese models)
Note
•Set to
On, the Auto Standby function may activate itself during
playback with some sources.
•The Auto
Standby function does not work when Zone 2/3 is on.
Network
This section explains how to configure the AV receiver’s
network settings manually.
If your router’s DHCP server is enabled, you don’t need to
change any of these settings, as the AV receiver is set to
use DHCP to configure itself automatically by default (i.e.,
DHCP is set to “Enable”). If, however, your router’s
DHCP server is disabled (you’re for example using static
IP), you’ll need to configure these settings yourself, in
which case, a knowledge of Ethernet networking is
essential.
What’s DHCP?
DHCP (Dynamic Host Configuration Protocol) is used by
routers, computers, the AV receiver, and other devices to
automatically configure themselves on a network.
What’s DNS?
The DNS (Domain Name System) translates domain
names into IP addresses. For example, when you enter a
domain name such as www.onkyousa.com in your Web
browser, before accessing the site, your browser uses DNS
to translate this into an IP address, in this case
63.148.251.142.
MAC Address
This is the AV receiver’s MAC (Media Access Control)
address. This address cannot be changed.
DHCP
` Enable
` Disable
This setting determines whether or not the AV receiver
uses DHCP to automatically configure its IP Address,
Subnet Mask, Gateway, and DNS Server settings.
Note
If you select “Disable”, you must configure the “IP Address”,
Subnet Mask”, “Gateway”, and “DNS Server” settings
yourself.
After changing the settings of the “HDMI
Control(RIHD)”, “HDMI Through” or “Audio
Return Channel”, turn off the power on all connected
pieces of equipment and then turn them on again. Refer
to the user’s manuals for all connected pieces of
equipment.
After modifying the network settings, you must confirm
the changes by executing “Save”.
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR 717 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR 717 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR 717

Onkyo TX-NR 717 User Manual - German - 144 pages

Onkyo TX-NR 717 User Manual - Dutch - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info