492647
55
Zoom out
Zoom in
Previous page
1/148
Next page
Advanced Operations
En-55
Main Menu Speaker Setup
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the
connected speakers after using Audyssey 2EQ Room
Correction and Speaker Setup function.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
Speakers Type(Front)” setting. For details on speaker
wire connection, see “Bi-amping the Front Speakers”
( page 14).
Note
When bi-amping is used, the AV receiver is able to drive up to 5.1
speakers in the main room.
Before you change these settings, turn down the volume.
Speaker Impedance
` 4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
` 6ohms:
Select if the impedances of all speakers are between 6
and 16 ohms.
Speakers Type(Front)
` Normal
:
Select this if you’ve connected your front speakers
normally.
` Bi-Amp:
Select this if you’ve bi-amped your front speakers.
Powered Zone 2, Powered Zone 3
` No
` Yes:
Zone 2/3 speakers can be used. (Powered Zone 2/3
enabled).
Note
If the “Speakers Type(Front)” setting is set to “Bi-Amp”,
Powered Zone 2/3 cannot be used.
When the “Powered Zone 2” setting is set to “Yes” and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
If the “Powered Zone 2” setting is set to “No”, the “Powered
Zone 3” setting cannot be selected.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey 2EQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to “80Hz(THX)” crossover.
Subwoofer
` Yes
` No
Front
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz, 200Hz
Note
If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
Center
*1
, Surround
*1*2
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz, 200Hz
` None
Front Wide
*1*3*4
, Front High
*1*3*5*6
` Full Band
` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz
` None
Surround Back
*1*2*3*5
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz, 200Hz
` None
Note
*1
Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
When the “Powered Zone 3” setting is set to “Yes” and
Zone 3 is turned on, this setting cannot be selected.
*3
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*4
If the “Speakers Type(Front)” setting is set to “Bi-Amp”, or
the “Powered Zone 2” setting is set to “Yes”, this setting
cannot be selected.
*5
If the “Speakers Type(Front)” setting is set to “Bi-Amp”, or
the “Powered Zone 2” setting is set to “Yes” together with
Zone 2 turned on, this setting cannot be selected.
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey 2EQ
®
Room Correction and Speaker Setup
( page 35).
If you change these settings, you must run
Audyssey 2EQ Room Correction and Speaker Setup
again ( page 35).
1 2 3 4 5
Setup
This setting is set automatically by Audyssey 2EQ Room
Correction and Speaker Setup ( page 35).
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR 717 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR 717 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR 717

Onkyo TX-NR 717 User Manual - German - 144 pages

Onkyo TX-NR 717 User Manual - Dutch - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info