553757
22
Zoom out
Zoom in
Previous page
1/76
Next page
22
Operating components not reached by the
remote controller signals (IR IN/OUT)
If the remote controller signal does not reach the
TX-DS797 remote sensor
If the TX-DS797 is located inside a cabinet or other enclosure where
the infrared rays from the remote controller cannot enter, then
operation with the remote controller will not be possible. In such a
case, it will be necessary to install a remote sensor at a location
outside of the cabinet for the infrared rays from the controller to
reach.
With this connection, select Main for the Hardware Setup IR IN
Setup Position setting in the Setup menu (see page 28).
If the remote controller signal does not reach
other components
In this situation, you will need to use a commercially available IR
emitter. Connect the mini plug of the IR emitter to the IR OUT
terminal on the TX-DS797 and then place the IR emitter on the
remote sensor of the component or facing it. When the IR emitter is
connected, only the signal input to the IR IN terminal is output to the
IR OUT terminal. The signal input from the remote sensor on the
front of the TX-DS797 will not be output to the IR OUT terminal.
The following equipment (sold separately) is essential for
operation:
Onkyos Multi-Room System kits (IR Remote Controller
Extension System), or
Multiroom A/V distribution and control systems from Niles
®
and Xantech
®
to name a few
The IR IN input allows you to control the TX-DS797 from the
remote zone (Zone 2) with the remote controller even though the
remote zone is physically separated. The diagram below shows how
to make the proper connections for the remote zone.
With this connection, select Zone 2 for the Hardware Setup IR
IN Setup Position setting in the Setup menu (see page 28).
Make connection as shown below. Do not plug the equipment into
the power source until the connection is complete.
from connecting block
IR IN
TX-DS797
In the
cabinet
Remote Controller
Connecting
block
IR Receiver
: Signal flow
Connecting
block
TX-DS797
Main room
: Signal flow
To IR IN
Zone 2 room
IR Receiver
Remote controller
IR IN
IR OUT
Connecting
block
IR Receiver
TX-DS797
IR Emitter
Remote Controller
other
component
: Signal flow
I
R
IN
OUT
12V TRIGGER
ZONE 2
REMOTE
CONTROL
Mini plug cable
TX-DS797
I
R
IN
OUT
12V TRIGGER
ZONE 2
REMOTE
CONTROL
Remote control
sensor
other component
Emitter
Mini plug cable
: Signal flow
Mini plug
IR Emitter
TX-DS797
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-DS797 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-DS797 in the language / languages: English as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-DS797

Onkyo TX-DS797 User Manual - German, Dutch - 218 pages

Onkyo TX-DS797 User Manual - French, Italian - 218 pages

Onkyo TX-DS797 User Manual - Swedish - 218 pages

Onkyo TX-DS797 User Manual - Spanish - 218 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info