553756

Onkyo TX-DS787 Manual

66
Zoom out
Zoom in
Previous page
1/76
Next page
66
Using a Macro function
Programming a Macro function
You can program a different macro into the MODE MACRO
button for each of the eight MODE buttons. The macro is then
executed by pressing the appropriate MODE button and then
pressing the MODE MACRO button. For example, to program the
macro described above into the CD MODE button, perform the
steps given below.
1. Press and hold down the desired MODE button (in
this case, the CD MODE button), press the MODE
MACRO button, and then release both buttons.
When you press the CD MODE button, the SEND/LEARN
indicator lights and “CD” appears in the display. When you
press the MODE MACRO button, the indicator turns off.
When you release the buttons, the indicator flashes and lights
again and “M 01” appears in the display.
2. Press the operation buttons you wish to
program in order (in this case, press AUDIO/
TAPE MODE → ON → CD (INPUT SELECTOR)
→ CD MODE → playback button).
When you press each button, the SEND/LEARN indicator turns
off and the display changes from “M 01” → “M 02” → “M 03”
→ etc. When you release the button, the indicator lights.
3. Press the MODE MACRO button to complete
the programming.
The SEND/LEARN indicator flashes twice slowly and
“SAVED” appears in the display.
4. Run the macro to check to see if the macro has
been properly programmed.
Notes:
• You may program up to 16 button operations into each macro
function. If you try to program a 17th operation, it will be
ignored, “SAVED” appears in the display, and programming
is stopped.
• If no button is pressed for more than 30 seconds during the
programming, the SEND/LEARN indicator flashes three times
quickly, “ERROR” appears in the display, and the remote
controller exits the programming mode. Resume from Step 1.
• If you perform an invalid operation during programming, the
SEND/LEARN indicator flashes three times quickly,
“ERROR” appears in the display, and the remote controller
exits the programming mode. Resume from Step 1.
Running a Macro function
Perform the procedure below to run a macro function that you
have programmed into the remote controller. After programming a
macro, you should always run it at least once to make sure that it
has been programmed properly.
1. Point the remote controller at the TX-DS787
and press the CD MODE button.
2. Press the MODE MACRO, and verify that the
devices operate properly.
It may take a while for the macro to finish transmitting, so be
sure to continue pointing the remote controller at the device
until the SEND/LEARN indicator turns off.
Tip:
• If you erase or change the command of a button programmed
in a macro, that operation of that button will no longer work in
the macro. In this case, it will be necessary for you to
reprogram the macro in order to avoid incorrect operation.
• The codes programmed into a macro will be transmitted at an
interval of 0.5 seconds. However, some devices may not be
able to complete one operation in 0.5 seconds and may miss
the next code. In this case, after pressing one operation button,
you can press the same MODE button again before pressing
the next operation button to add another 0.5 seconds between
the two operations.
OPEN/CLOSEREC
AUDIO MUTING
DISCTRACK
DVD
CD
PH
TUN
T2T1
V1
STEREO
123
654
7
+
10 0
ENT
89
SURROUND THX DSP
LEVEL
+
CH SELRe-EQ
LEVEL
–
DIMMER
HOME THEATER CONTROLLER
RC-390M
LATE NIGHT
DIRECT DSP
V2 V3 V
–
MODE MACRO
CD MODE
CD
ON
AUDIO/TAPE
MODE
(CD playback)
(INPUT
SELECTOR)
What is a Macro function?
A Macro function enables you to program a series of button
operations (up to 16) on the remote controller into a single button.
For example, to play a compact disc player connected to the TX-
DS787 normally, you must perform the following steps:
1. Press the AUDIO/TAPE MODE button.
2. Press the ON button.
3. Press the CD (INPUT SELECTOR) button.
4. Press the CD MODE button.
5. Press the playback button.
By using the macro function, you can perform the above five
operations by only pressing two buttons.
… 66 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-DS787 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-DS787 in the language / languages: English as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-DS787

Onkyo TX-DS787 User Manual - French - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info