553756
63
Zoom out
Zoom in
Previous page
1/76
Next page
63
Programming the commands of remote controllers for
other devices into the remote controller
5 to 15 cm
(2 to 6 inches)
Buttons that cannot be programmed.
P
O
W
E
R
S
LE
E
P
D
IM
M
E
R
S
U
R
M
O
D
E
V
ID
EO
-1
V
ID
EO
-2
T
A
P
E
D
VD
C
D
C
D
D
V
D
TU
N
E
R
TU
N
E
R
P
H
O
N
O
IN
P
U
T S
EL
E
C
T
O
R
D
IS
C
TA
P
E
V
O
LU
M
E
C
H
S
E
L
P
R
E
S
E
T
M
U
T
IN
G
T
ES
T
T
O
N
E
M
U
L
T
I-C
H
IN
P
U
T
G
RO
U
P
85
S
OPEN/CLOSEREC
AUDIO MUTING
DISCTRACK
DVD
CD
PH
TUN
T2T1
V1
STEREO
123
654
7
+
10 0
ENT
89
SURROUND THX DSP
LEVEL
+
CH SELRe-EQ
LEVEL
DIMMER
HOME THEATER CONTROLLER
RC-390M
LATE NIGHT
DIRECT DSP
V2 V3 V
ENT
DIRECT
MACRO
MODE
MACRO
LIGHT
:
SEND/LEARN
indicator
MODE
buttons
MODE
buttons
The remote controller has two learning functions. One is a normal
learning function that enables the remote controller to learn the
codes from other remote controllers. The other is a macro learning
function that enables you to program of series of operations into
the remote controller so that they can all be performed at once by
pressing one button.
Programming procedure
When programming the commands of another remote controller to
the RC-390M remote controller, you must first decide under which
MODE button you want the commands to be linked. In general,
you will select the MODE button that corresponds to the
component you are programming. For example, if you are
programming the functions from a remote controller for a compact
disc player, you would choose the CD MODE button. Then, by
pressing the CD MODE button, the buttons on the RC-390M
remote controller will change to the commands you program here
to operate the compact disc player.
After programming which MODE button to use, you will then
transfer the separate commands from the other remote controller
over to the RC-390M remote controller one at a time. Each
command is then programmed to a different button on the RC-
390M remote controller. Any button is programmable for this step
except for the eight MODE buttons (AUDIO, CD, DVD, MD,
SAT, CABLE, VCR, and TV), the two MACRO buttons (DIRECT
and MODE), and the LIGHT button.
Even after the commands have been memorized, keep your old
remote controller in a safe place. If for some reason the commands
are lost (e.g., when the batteries run down), it will be necessary to
memorize them once again.
1. Place the remote controller and the remote
controller for the other device facing each
other at a distance of 5 to 15 cm (2 to 6 inches)
apart.
2. While pressing and holding down the desired
MODE button on the remote controller, press
the ENT button and then release both buttons.
When you press and hold down the MODE button, the SEND/
LEARN indicator lights. When you press the ENT button, the
lamp turns off. When you release the buttons, the lamp lights
again and LEARN appears in the display.
3. Press and release the button on the remote
controller to which you want to transfer the
next command.
You may select any button but the eleven ones indicated in the
figure below. When you press the button, RCV appears in
the display and the SEND/LEARN indicator turns off. When
you release the button, the indicator lights again.
If you press the wrong button by mistake, press that same
button again. The SEND/LEARN indicator flashes twice,
CLEAR appears in the display, and the remote controller
exits the programming mode.
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-DS787 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-DS787 in the language / languages: English as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-DS787

Onkyo TX-DS787 User Manual - French - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info