553753
58
Zoom out
Zoom in
Previous page
1/64
Next page
58
Using a Macro function
Programming the Direct Macro function
With the direct macro function, you can program a series of button
operations as a macro into the DIRECT MACRO button so the
macro can be executed with just one touch. Note that for the direct
macro function, only one macro can be programmed. For example,
to program the macro described on the previous page for the
DIRECT MACRO button, perform the steps given below.
1. Press and hold down any one of the eight MODE
buttons, press the DIRECT MACRO button, and then
release both buttons.
When you press the MODE button, it lights green and the
SEND/LEARN indicator lights. When you press the DIRECT
MACRO button, the indicator turns off. When you release the
buttons, the indicator flashes briefly and then lights again.
2. Press the operation buttons you wish to program in
order (in this case, press RCVR MODE ON CD
(INPUT SELECTOR) CD MODE playback ( )
button).
When you press each button, the SEND/LEARN indicator turns
off. When you release the button, the indicator lights.
3. Press the DIRECT MACRO button to complete the
procedure.
The SEND/LEARN indicator flashes twice slowly.
4. Check to see if the macro has been properly
programmed.
Notes:
You may program up to 16 button operations into the direct
macro function. If you try to program a 17th operation, it will be
ignored, and programming is stopped.
If no button is pressed for more than 30 seconds during the
programming, the SEND/LEARN indicator flashes three times
quickly, and the remote controller exits the programming mode.
Resume from Step 1.
If you perform an invalid operation during programming, the
SEND/LEARN indicator flashes three times quickly, and the
remote controller exits the programming mode. Resume from
Step 1.
Running a Direct Macro function
Perform the procedure below to run a direct macro function that you
have programmed into the remote controller. After programming a
direct macro, you should always run it at least once to make sure that
it has been programmed properly.
1. Point the remote controller at the TX-DS696 and
press the DIRECT MACRO button.
It may take a while for the macro to finish transmitting, so be
sure to continue pointing the remote controller at the device until
the SEND/LEARN indicator turns off.
Tips:
If you erase or change the command of a button programmed in
the direct macro, that operation of that button will no longer
work in the macro. In this case, it will be necessary for you to
reprogram the direct macro in order to avoid incorrect operation.
The codes programmed into a direct macro will be transmitted at
an interval of 0.5 seconds. However, some devices may not be
able to complete one operation in 0.5 seconds and may miss the
next code. In this case, after pressing one operation button, you
can press the same MODE button again before pressing the next
operation button to add another 0.5 seconds between the two
operations.
HOME THEATER CONTROLLER
RC
-
440M
DIRECT MACRO CD MODE
RCVR MODE
ON
(CD playback)
CD
(INPUT
SELECTOR)
MODE buttons
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-DS696 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-DS696 in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-DS696

Onkyo TX-DS696 User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info