553753
19
Zoom out
Zoom in
Previous page
1/64
Next page
19
The TX-DS696 is shipped with the main power (POWER)
switch in the on position (
ON
). When the power cord is
plugged in for the first time, the TX-DS696 will automatically
enter the standby state and the STANDBY indicator will light
(same condition after step 2 below).
Before you plug in the TX-DS696, confirm that all connections
have been made properly.
Turning on the power may cause a momentary power surge,
which might interfere with other electrical equipment on the
same circuit, such as computers. If this happens, use a wall outlet
on a different circuit.
1. Plug the power cord into an AC wall outlet.
2. Press the ON button to turn on the
TX-DS696 (take it out of the standby
state).
To return the TX-DS696 to the standby
state, press the STDBY button.
Turning the power on from the remote controller:
Before you can use the remote controller, you must perform steps 1
and 2 above and place the TX-DS696 in the standby state.
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
Memory preservation
This unit does not require memory preservation batteries. A built-
in memory power backup system preserves the contents of the
memory during power failures and even when the POWER
switch is set to off. The POWER switch must be set to on in order
to charge the backup system.
The memory preservation period after the unit has been turned off
varies depending on climate and placement of the unit. On the
average, memory contents are protected over a period of a few
weeks after the last time the unit has been turned off. This period
is shorter when the unit is exposed to a highly humid climate.
3. Press the STANDBY/ON button to
turn on the TX-DS696. The display
and four jog dial indicators will light
up and the STANDBY indicator will
turn off.
If you press the STANDBY/ON button
again, the receiver returns to Standby mode.
2. Press the POWER switch to set the
TX-DS696 to standby state.
The STANDBY indicator will light up.
To change the display of the input source from TAPE to
MD:
If you connected an MD recorder to the TAPE jack on the TX-
DS696, you can have MD appear when the TAPE source button is
pressed. By changing the display, if an Onkyo MD recorder z-
connected, the z system functions will become enabled.
Changing the display:
Press and hold down the TAPE source button until the display
changes from TAPE to MD (approx. 3 seconds).
To return the display to its original setting, perform the same
procedure. This setting is necessary to allow z system functions
for the connected cassette tape or MD recorder.
STANDBY/ON
STANDBY
OFF
ON
POWER
MASTER VOLUME
BASS
TREBLE
AV
RECEIVER
TX
-
DS
696
PHONES
FM AM PHONO C
DTAPEDVD
REC OUT
ZONE
2
ZONE
2
LEVEL
CH LEVEL
VIDEO
3
VIDEO
4
VIDEO
2
VIDEO
1
VCR
2
VCR
1
AUDIO
SELECTOR
TUNING PRESET
SMART
SCAN
NAVIGATOR
PRESET MEMORY
FM
MODEDISPLAY DIMMER
PUSH TO ENTER
DSP
/
MODE ADJ
SETUP
RETURN
MUTING
HOME THEATER CONTROLLER
RC
-
440M
POWER
STANDBY/ON
ON
RCVR MODE
STDBY
Connecting the power
STANDBY indicator
SEND/LEARN
indicator
To wall outlet
STANDBY
OFF
ON
POWER
STANDBY/ON
STANDBY
Turn off
TAPE
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-DS696 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-DS696 in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-DS696

Onkyo TX-DS696 User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info