553752
11
Zoom out
Zoom in
Previous page
1/52
Next page
11
Connections
REMOTE
CONTROL
FM
75
AM
ANTENNA
GND
IN
OUT
IN
IN
IN
L
R
CENTER
SUB
WOOFER
FRONT
SURR
SUBWOOFER
OPTICAL
COAXIAL
1
2
12
PRE OUT
MULTI
CHANNEL INPUT
DIGITAL
INPUT
L
R
OUT
IN
PHONO
TAPE
CD
MONITOR
OUT
DVD
VIDE
O
VIDEO
2
VIDEO
1
L (White)
R (Red)
L (White)
R (Red)
3. Tape deck, MD recorder,
DAT deck, CD recorder,
(TAPE)
Analog audio input
Analog audio output
1. Turntable
(PHONO)
Analog audio output
Ground wire (earth)
L (White)
R (Red)
2. CD player
(CD)
Analog audio output
Digital audio output (optical)
L (White)
R (Red)
Connecting your audio components
Below is an example of how you can connect your audio
components to the TX-DS595. Refer to the diagram above for the
following connection examples.
1. Connecting a turntable (PHONO)
Using an RCA-type audio connection cable, connect the output
terminal on the turntable to the PHONO input jacks on the TX-
DS595. Make sure that you properly connect the left channel to the L
jack and the right channel to the R jack.
Note:
The TX-DS595 is designed for use with moving magnet cartridges.
For proper operation, connect a ground (or earth) wire to the GND
terminal. For some turntables, however, connecting the ground wire
may cause increased noise, and in such a case, a ground wire is not
necessary and should not be connected.
2. Connecting a compact disc player (CD)
Using an RCA-type audio connection cable, connect the output
terminal on the compact disc player to the CD input jacks on the TX-
DS595. Make sure that you properly connect the left channel to the L
jack and the right channel to the R jack.
If the compact disc player has a digital output jack as well, be sure to
also connect it to either a DIGITAL INPUT (COAXIAL) or
DIGITAL INPUT (OPTICAL) jack on the TX-DS595 depending on
the type of connector on the compact disc player.
With the initial settings of the TX-DS595, the CD input source is
set for digital input at the OPTICAL 1 jack.
If the digital connection is made at a different jack, this must be
changed at the setup menu: Input Setup Audio Setup Digital
Input (see page 29).
3. Connecting a cassette tape deck, MD recorder, DAT
deck, or CD recorder (TAPE)
Using an RCA-type audio connection cable, connect the output
terminals (PLAY) of the device to the TAPE IN jacks on the TX-
DS595 and the input terminals (REC) to the TAPE OUT jacks. Make
sure that you properly connect the left channel to the L jack and the
right channel to the R jack.
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the TX-DS595 depending on the type of
connector on the device.
With the initial settings of the TX-DS595, the TAPE input source
is set for no digital input.
If you connect the device to the DIGITAL INPUT terminal, then this
input source must be set for digital input at the setup menu: Input
Setup Audio Setup Digital Input (see page 29).
Audio connection cable: Signal flow
Left (White)
Right (Red)
L
R
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-DS595 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-DS595 in the language / languages: English as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-DS595

Onkyo TX-DS595 User Manual - French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info