66920
12
Zoom out
Zoom in
Previous page
1/36
Next page
12
Connecting Your Speakers
Disconnect the power cord from the wall outlet before making any connections.
The receiver allows you to connect two sets of speakers.
When two sets of speakers are connected, you can select
which speaker set outputs sound or use both sets to
output sound simultaneously.
When you connect one set of speakers to either
SPEAKERS A or SPEAKERS B terminal posts, or
when you connect two sets of speakers to both speaker
terminal posts and output sound only from either
speaker set, use speakers whose impedance is between
4 and 16 ohms. For the North American model
TX-8522, when the speaker impedance is 4 or 6 ohms,
set the speaker impedance setting on the receiver to 6
ohms (see next page for details).
When you connect speakers to both SPEAKER A and
SPEAKER B terminal posts and output sound from
both speaker sets simultaneously, use speakers whose
impedance is between 8 and 16 ohms.
Note:
If you make an incorrect setting for the speakers or the
impedance values, the built-in protection circuit may be
activated resulting in no sound output from speakers.
The following illustration shows which speaker should
be connected to each pair of terminals.
Read the instructions supplied with your speakers.
Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive
(+) terminals, and negative () terminals only to
negative () terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
Unnecessarily long or very thin speaker cables may
affect the sound quality and should be avoided.
Be careful not to short the
positive and negative wires.
Doing so may damage the
receiver.
Dont connect more than one
cable to each speaker
terminal. Doing so may
damage the receiver.
Dont connect a speaker to more than one pair of
speaker terminals.
Speaker Connection Precautions
+
+ +
+
Speaker set A
Left
speaker
Right
speaker
Speaker set B
Left
speaker
Right
speaker
Receiver
Connecting the Speaker Cables
1
Strip about 15 mm (5/8
inch) of insulation from
the ends of the speaker
cables, and twist the bare
wires tightly, as shown.
2
Unscrew the terminal.
3
Fully insert the bare
wires.
4
Screw the terminal tight.
15 mm
(5/8")
TX-85228222_En.book 12 ページ 2006年5月4日 木曜日 午前11時51分
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-8522 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-8522 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-8522

Onkyo TX-8522 User Manual - German - 72 pages

Onkyo TX-8522 User Manual - Dutch - 72 pages

Onkyo TX-8522 User Manual - Dutch, Italian - 72 pages

Onkyo TX-8522 User Manual - Swedish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info